Relay test set
kc4ums·relay_test_set·Kicad/Kicad.kicad_sch
About the Relay test set PCB
Relay test set is an open source PCB design by kc4ums, published on GitHub under the GPL-3.0 license. It is a board, with 16 components from 11 distinct parts.
Other key parts include the LM358_Single and X9C104. By type, the board carries 6 resistors, 2 ICs, 2 transistors, 2 diodes, 2 capacitors and 1 connector.
It belongs with the test & measurement and usb & debug tools designs in this gallery.
From the project
3 Phase Secondary Relay Test Set
Generates three-phase 60Hz sine waves to simulate motor starting inrush current for overcurrent relay testing. Amplitude, inrush profile, and decay are all controlled programmatically via a serial console — no external digital potentiometer required.
The C2000 outputs 100kHz PWM on three ePWM channels. Duty cycle is updated at 15,360 Hz (256 steps × 60Hz) from a sine lookup table. The ISR scales each channel's amplitude in real time, implementing the inrush profile in firmware. RC filters remove the PWM carrier, leaving a clean 60Hz sine. MOSFET push-pull amplifiers (IRF540N + IRF9540N)…
Main components on the Relay test set
Relay test set bill of materials (BOM)
16 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM358_Single | U1 | |
| 1 | X9C104 | DIP-8_W7.62mm | U2 |
| 1 | IRF540N | TO-220-3_Vertical | Q1 |
| 1 | IRF9540N | TO-220-3_Vertical | Q2 |
| 1 | Conn_01x02 | J1 | |
| 1 | 10k | RV1 | |
| 2 | 1N4148 | D1, D2 | |
| 2 | 100nF | C1, C2 | |
| 3 | 1k | R1, R2, R3 | |
| 2 | 220 | R4, R5 | |
| 1 | 0.05 | R6 |
Relay test set design files
The KiCad project lives in the kc4ums/relay_test_set repository on GitHub; these links point at the commit this page was built from.
- SchematicKicad/Kicad.kicad_sch
Relay test set: common questions
How many components are on the Relay test set?
16 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the Relay test set design files?
From the kc4ums/relay_test_set repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Relay test set design in my own project?
Yes, under the terms of its GPL-3.0 license, which kc4ums chose for the repository.
Similar boards
StackLink
gusmanb
52.3 × 10.5 mm5 parts2LGPL-3.05.0kAnalyzerBoxPCB fork
gusmanb
52.7 × 47.9 mm54 parts4LGPL-3.05.0kLevelShifter
gusmanb
28.3 × 39.8 mm21 parts2LGPL-3.05.0kXG Station Power
osy
54.3 × 91 mm9 parts2LCC-BY-4.0703USB Hub Test
osy
50 × 50 mm85 parts4LCC-BY-4.0703EleLab v2 PowerFeed
Chrismettal
68 × 50 mm11 parts2LGPL-3.0528