GripperBoard

keagoesdeep·gripperBoard_PCB

This repository ships a schematic but no board layout.

About the GripperBoard PCB

GripperBoard is an open source STM32 PCB design by keagoesdeep, published on GitHub. It is a board, with 79 components from 38 distinct parts.

Its main chip is the STM32F042C6Tx, from the STM32 family. Other key parts include the LP2985-3.3, INA199, DRV8886ATPWP and TJA1051TK/3. By type, the board carries 36 capacitors, 22 resistors, 12 connectors, 7 ICs, 1 crystal and 1 diode.

From the project

PCB design of board used for controlling Gripper for KEA Goes Deep's ROV

link to the ised libraries: https://github.com/lakotamm/lakotamm-kicad-lib

Main components on the GripperBoard

GripperBoard bill of materials (BOM)

79 components, 38 distinct parts.

QtyPartRefs
1
LP2985-3.3
U1
1
STM32F042C6Tx
U2
2
INA199
U3, U5
2
DRV8886ATPWP
DRV8886AT
U4, U6
1
TJA1051TK/3
U7
1
Crystal 24Mhz
Y1
1
UART
J1
1
CAN_1
J2
1
CAN_2
J3
1
SWD
J4
1
MOT1_AOUT1
J5
1
MOT1_AOUT2
J6
1
MOT1_BOUT1
J7
1
MOT1_BOUT2
J8
1
MOT2_AOUT1
J9
1
MOT2_AOUT2
J10
1
MOT2_BOUT1
J11
1
MOT2_BOUT2
J12
1
D_Schottky
D1
3
C
C1, C16, C28
Show 18 more
QtyPartRefs
2
CP
C2, C3
2
12p 25V
C4, C6
1
>1uF 16V
C5
6
100n 6V3
C7, C10, C11, C12, C21, C26
1
10n 6V3
C8
1
2u2 6V3
C9
2
4u7 6V3
C13, C14
3
1u 6V3
C15, C25, C27
4
470nF 6V3
C17, C19, C29, C31
4
10n 16V
C18, C20, C30, C32
2
C
C22, C33
2
220nF 16V
C23, C34
2
22nF 16V
C24, C35
1
100n
C36
18
R
R1, R2, R3, R4, R5, R6, R7, R9 +10
1
NM
R8
1
3k3
R10
2
R_Shunt
R11, R17

GripperBoard design files

The KiCad project lives in the keagoesdeep/gripperBoard_PCB repository on GitHub; these links point at the commit this page was built from.

GripperBoard: common questions

What microcontroller does the GripperBoard use?

The GripperBoard is built around the STM32F042C6Tx, from the STM32 family.

How many components are on the GripperBoard?

79 components, from 38 distinct parts. The full bill of materials is listed on this page.

Where can I download the GripperBoard design files?

From the keagoesdeep/gripperBoard_PCB repository on GitHub, which has the schematic and a netlist; the links under Design files point to each one.

Can I use the GripperBoard design in my own project?

The repository has no license, so all rights stay with keagoesdeep. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the GripperBoard without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards