KSZ9031RNXCC
Lampranthus·KSZ9031RNXCC-PCB·hardware/PCB_Ethernet-1Gbps-Spartan-6/PCB_Ethernet-1Gbps-Spartan-6.kicad_pcb
About the KSZ9031RNXCC PCB
KSZ9031RNXCC is an open source PCB design by Lampranthus, published on GitHub under the MIT license. It is a 2-layer board measuring 54 × 47.5 mm, with 63 components from 20 distinct parts.
Other key parts include the KSZ9031RNXCC and LD1117S12TR_SOT223. By type, the board carries 29 capacitors, 18 resistors, 4 connectors, 3 fuses, 2 ICs and 2 LEDs.
From the project
A 1 Gbps Ethernet UDP communication system implemented on a Xilinx Spartan-6 FPGA with a KSZ9031 Gigabit PHY. Achieves ~1 Gbps throughput in TX, RX, and full-duplex modes, controlled via UART or UDP commands.
A 1 Gbps Ethernet UDP communication system implemented on a Xilinx Spartan-6 FPGA with a KSZ9031 Gigabit PHY. Achieves ~1 Gbps throughput in TX, RX, and full-duplex modes, controlled via UART or UDP commands.
- UDP TX/RX at line rate (~1 Gbps) - Full-duplex simultaneous TX + RX (237 MB/s measured) - UART control interface — configure and trigger tests via serial commands - UDP command interface — remotely set packet count, size, and rate - ARP support — FPGA responds to ARP requests - Software shutdown mode — low-power state via command (~159 mA)
Main components on the KSZ9031RNXCC
KSZ9031RNXCC bill of materials (BOM)
63 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | KSZ9031RNXCC | IC_KSZ9031RNXCC | U2 |
| 1 | LD1117S12TR_SOT223 | SOT-223-3_TabPin2 | U3 |
| 1 | PMOS | SOT-23_Handsoldering | Q1 |
| 1 | 25MHZ 25Mhz | Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | ARJM11B1-502-AB-EW2 | ABRACON_ARJM11B1-502-AB-EW2 | J1 |
| 1 | CONN_02X20_ODD_EVEN Conn_02x20_Odd_Even | PinSocket_2x20_P2.54mm_Horizontal | J2 |
| 1 | CONN_01X02_PIN Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | CONN_01X01_PIN Conn_01x01_Pin | PinHeader_1x01_P2.54mm_Vertical | J4 |
| 3 | 0 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | F1, F2, F3 |
| 1 | 0 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | JP1 |
| 2 | LED | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | 3V3, 5V0 |
| 2 | 1N4148 | D_SOD-123F | D1, D2 |
| 6 | 10UF 10uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C8, C25, C26, C27, C29 |
| 2 | 22PF 22pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3 |
| 21 | 0.1UF 0.1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C5, C6, C7, C9, C10, C11, C12 +13 |
| 1 | 12.1K 12.1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 10 | 10K 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3, R4, R5, R6, R7, R8, R9 +2 |
| 2 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R15 |
| 4 | 220 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13, R14, R17, R18 |
| 1 | 120 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R16 |
KSZ9031RNXCC design files
The KiCad project lives in the Lampranthus/KSZ9031RNXCC-PCB repository on GitHub; these links point at the commit this page was built from.
KSZ9031RNXCC: common questions
How big is the KSZ9031RNXCC PCB?
The KSZ9031RNXCC measures 54 × 47.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the KSZ9031RNXCC?
63 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the KSZ9031RNXCC design files?
From the Lampranthus/KSZ9031RNXCC-PCB repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the KSZ9031RNXCC design in my own project?
Yes, under the terms of its MIT license, which Lampranthus chose for the repository.