QIC02EMU
MattisLind·QIC02EMU·QIC02EMU/QIC02EMU.kicad_pcb
About the QIC02EMU PCB
QIC02EMU is an open source STM32 PCB design by MattisLind, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 95.3 × 76.2 mm, with 20 components from 11 distinct parts.
Its main chip is the STM32BluePill, from the STM32 family. Other key parts include the 74ABT657, 74ABT241 and 74LVC1G04. By type, the board carries 9 resistors, 4 ICs, 4 capacitors and 3 connectors.
From the project
Device that is supposed to emulate a generic QIC-02 tape drive or specifically the IBM6157 tape drive. The IBM 6157 contains a Cipher 450 tape drive. But has a 37 pin DUSB interface cable rather than the 50 pin IDC type connector.
Device that is supposed to emulate a generic QIC-02 tape drive or specifically the IBM6157 tape drive. The IBM 6157 contains a Cipher 450 tape drive. But has a 37 pin DUSB interface cable rather than the 50 pin IDC type connector.
The card is supposed to plug directly into the IBM RT PC 6157 streaming tape controller board without using any cable.
Initially only reading of tape will be supported but later on writing will be implemented.

Main components on the QIC02EMU
QIC02EMU bill of materials (BOM)
20 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32BluePill | DIP-40_W15.24mm | U1 |
| 1 | 74ABT657 | SOIC-24W_7.5x15.4mm_P1.27mm | U2 |
| 1 | 74ABT241 | SOIC-20W_7.5x12.8mm_P1.27mm | U3 |
| 1 | 74LVC1G04 | SOT-23-5 | U4 |
| 1 | 2.5 mm Barrel DC JACK | BarrelJack_Horizontal | J1 |
| 1 | Micro_SD_Card_Det | microSD_HC_Hirose_DM3AT-SF-PEJM5 | J2 |
| 1 | 50 Pin header | IDC-Header_2x25_P2.54mm_Vertical | J3 |
| 1 | 10u | CP_Radial_D6.3mm_P2.50mm | C1 |
| 3 | 100n | C_0805_2012Metric | C2, C3, C4 |
| 7 | 68k | R_0805_2012Metric | R1, R2, R3, R4, R5, R6, R7 |
| 2 | 330/220 ohm SIP | R_Array_SIP10 | RN1, RN2 |
QIC02EMU design files
The KiCad project lives in the MattisLind/QIC02EMU repository on GitHub; these links point at the commit this page was built from.
QIC02EMU: common questions
What microcontroller does the QIC02EMU use?
The QIC02EMU is built around the STM32BluePill, from the STM32 family.
How big is the QIC02EMU PCB?
The QIC02EMU measures 95.3 × 76.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the QIC02EMU?
20 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the QIC02EMU design files?
From the MattisLind/QIC02EMU repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the QIC02EMU design in my own project?
Yes, under the terms of its Apache-2.0 license, which MattisLind chose for the repository.
Can I test firmware for the QIC02EMU without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k