HardLabs

Stm8s target v1.1

MKesenheimer·fault-injection-library·schematics/kicad/stm8s-target-v1.1/stm8s-target-v1.1.kicad_pcb

Stm8s target v1.1 PCB layout, top view — open source STM32 board by MKesenheimer

About the Stm8s target v1.1 PCB

Stm8s target v1.1 is an open source STM32 PCB design by MKesenheimer, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 57 × 25.5 mm, with 40 components from 29 distinct parts.

Its main chip is the STM8S003F3U, from the STM32 family. Other key parts include the SN74LVC8T245PWR. By type, the board carries 11 resistors, 10 connectors, 8 diodes, 7 capacitors, 3 ICs and 1 switch.

From the project

Python library to perform fault-injection attacks on microcontrollers

Findus (aka the fault-injection-library) is a toolchain to perform fault-injection attacks on microcontrollers and other targets. This library offers an easy entry point to carry out fault-injection attacks against microcontrollers, SoCs and MCUs. With the provided and easy to use functions and classes, fault-injection projects can be realized quickly with cheap and available hardware.

Stm8s target v1.1, from the project README
From the project README

Main components on the Stm8s target v1.1

SN74LVC8T245PWRSTM8S003F3U

Stm8s target v1.1 bill of materials (BOM)

40 components, 29 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
SN74LVC8T245PWR
AMS1117-3.3
U1
1
SN74LVC8T245PWR
CH340X
U2
1
STM8S003F3U
U3
1
ISP_MODE
J1
1
VCAP
J2
1
TX/RX
J3
1
UART
J4
1
PROGRAM/DEBUG
J5
1
GPIO
J6
1
USB_C_Receptacle_USB2.0_16P
J7
1
Conn_Coaxial
J8
1
GLITCH_IN
J9
1
RESET
J10
1
KMR221GLFS
S1
1
LED_RED_3.3V
D1
1
LED_GREEN_GPIO
D2
1
LED_BLUE_GPIO
D3
1
LED_RED_TX
D4
1
LED_BLUE_RX
D5
3
D_Small
D6, D7, D8
Show 9 more
QtyPartRefs
1
10NF
10u
C1
1
2.2UF
10u
C2
2
100NF
0.1uF
C3, C7
2
100NF
10nF
C4, C5
1
100NF
1uF
C6
2
5.1k
R1, R2
5
150
R3, R4, R5, R6, R7
3
4.7k
R8, R9, R10
1
100
R12

Stm8s target v1.1 design files

The KiCad project lives in the MKesenheimer/fault-injection-library repository on GitHub; these links point at the commit this page was built from.

Stm8s target v1.1: common questions

What microcontroller does the Stm8s target v1.1 use?

The Stm8s target v1.1 is built around the STM8S003F3U, from the STM32 family.

How big is the Stm8s target v1.1 PCB?

The Stm8s target v1.1 measures 57 × 25.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Stm8s target v1.1?

40 components, from 29 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Stm8s target v1.1 design files?

From the MKesenheimer/fault-injection-library repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Stm8s target v1.1 design in my own project?

Yes, under the terms of its GPL-3.0 license, which MKesenheimer chose for the repository.

Can I test firmware for the Stm8s target v1.1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in fault-injection-library

Similar boards