Wacca ws2813
mnm-isola·wacca_ws2813·wacca_ws2813_rev1/wacca_ws2813.kicad_pcb
About the Wacca ws2813 PCB
Wacca ws2813 is an open source PCB design by mnm-isola, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 220 × 18 mm, with 24 components from 7 distinct parts.
Other key parts include the 1503a. By type, the board carries 9 capacitors, 8 diodes, 3 connectors, 2 ICs and 2 resistors.
It belongs with the displays & leds designs in this gallery.
From the project
No redundancy = bad design
According to page 7: These LEDs are moisture sensitive, they need to be baked and dried before SMT assembly. Not all PCB fabs have this procedure (eg JLCPCB's economic option), be sure to consult and notify the fab of your choice before mass producing the PCBs, otherwise you may end up with extremely high failure rate. (I learnt it the hard way so you don't have to.)
Main components on the Wacca ws2813
Wacca ws2813 bill of materials (BOM)
24 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 1503a | TSOT-23_HandSoldering | U1, U2 |
| 2 | JST XA 3p | JST_XA_B03B-XASK-1_1x03_P2.50mm_Vertical | CN1, CN2 |
| 1 | JST XA 4p | JST_XA_B04B-XASK-1_1x04_P2.50mm_Vertical | CN3 |
| 8 | WS2813 | LED_WS2812_PLCC6_5.0x5.0mm_P1.6mm | D1, D2, D3, D4, D5, D6, D7, D8 |
| 8 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4, C5, C6, C7, C8 |
| 1 | 1000uF | CP_Radial_D5.0mm_P2.50mm | C9 |
| 2 | 100 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
Wacca ws2813 design files
The KiCad project lives in the mnm-isola/wacca_ws2813 repository on GitHub; these links point at the commit this page was built from.
Wacca ws2813: common questions
How big is the Wacca ws2813 PCB?
The Wacca ws2813 measures 220 × 18 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Wacca ws2813?
24 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Wacca ws2813 design files?
From the mnm-isola/wacca_ws2813 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Wacca ws2813 design in my own project?
Yes, under the terms of its GPL-3.0 license, which mnm-isola chose for the repository.
Similar boards
LevelShifterBreakout
scottbez1
15.2 × 20.3 mm5 parts2LApache-2.022.2kView base
scottbez1
81.2 × 81.2 mm81 parts2LApache-2.022.2kView screen
scottbez1
35 × 35 mm12 parts2LApache-2.022.2kBM28B0.6-24DSBreakout
scottbez1
15.2 × 35.6 mm3 parts2LApache-2.022.2kChainlinkDriverTester
scottbez1
198.1 × 95.3 mm123 parts2LApache-2.04.2kChainlinkBase
scottbez1
98.4 × 190.5 mm119 parts2LApache-2.04.2k