NPulse v4
N-Pulse·ARM-ELEC-CTRL·NPulse_v4/NPulse_v4.kicad_pcb
About the NPulse v4 PCB
NPulse v4 is an open source STM32 PCB design by N-Pulse, published on GitHub under the CC-BY-4.0 license. It is a 4-layer board measuring 39.8 × 72.5 mm, with 157 components from 27 distinct parts.
Its main chip is the STM32G484METx, from the STM32 family. Other key parts include the TXU0202QDCURQ1, DRV8220DSGR, SN74LVC002 and TPS7A0533PDBZ. By type, the board carries 70 capacitors, 36 resistors, 19 ICs, 17 inductors, 9 connectors and 2 transistors.
It belongs with the robotics & motion designs in this gallery, and the repository also holds 1 earlier revision of it.
Main components on the NPulse v4
NPulse v4 bill of materials (BOM)
157 components, 27 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TXU0202QDCURQ1 TXU0202QDCUR | SOP50P310X90-8N | IC1 |
| 8 | DRV8220DSGR | WSON8_DSG_TEX | IC2, IC3, IC4, IC5, IC6, IC7, IC8, IC9 |
| 1 | STM32G484METx | LQFP-80_12x12mm_P0.5mm | U1 |
| 8 | SN74LVC002 | DHVQFN-14-1EP_2.5x3mm_P0.5mm_EP1x1.5mm | U2, U3, U4, U5, U6, U7, U8, U9 |
| 1 | TPS7A0533PDBZ | SOT-23 | U10 |
| 1 | PMOS | SOT95P240X120-3N | Q1 |
| 1 | NMOS | SOT95P240X120-3N | Q2 |
| 1 | 16MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 2 | Conn_01x04_Pin | PinHeader_1x04_P2.00mm_Vertical_SMD_Pin1Left | J2, J4 |
| 1 | Conn_01x06_Pin | PinHeader_1x06_P2.54mm_Vertical_SMD_Pin1Left | J3 |
| 6 | Conn_02x05_Odd_Even | PinHeader_2x05_P2.00mm_Vertical_SMD | J5, J6, J7, J8, J9, J10 |
| 1 | SW_Push | SW_SPST_TL3305B | SW1 |
| 1 | SW_SPDT | SW_SPDT_PCM12 | SW2 |
| 1 | LED | SOD6439X180N | D1 |
| 1 | 120R | L_0402_1005Metric | FB1 |
| 16 | 10uH | L_1008_2520Metric | L1, L2, L3, L4, L5, L6, L7, L8 +8 |
| 25 | 10uF | C_0805_2012Metric | C1, C26, C28, C29, C30, C33, C34, C38 +17 |
| 37 | 100nF | C_0402_1005Metric | C2, C3, C4, C5, C6, C7, C12, C13 +29 |
| 1 | 10nF | C_0402_1005Metric | C8 |
| 5 | 1uF | C_0402_1005Metric | C9, C10, C11, C55, C56 |
Show 7 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 10pF | C_0402_1005Metric | C14, C15 |
| 20 | 1k | R_0402_1005Metric | R1, R2, R3, R4, R5, R14, R15, R16 +12 |
| 4 | 10k | R_0402_1005Metric | R6, R7, R9, R10 |
| 1 | 47k | R_0402_1005Metric | R8 |
| 2 | 100k | R_0402_1005Metric | R11, R12 |
| 1 | 1M | R_0805_2012Metric | R13 |
| 8 | 1 | R_0612_1632Metric | R23, R24, R27, R28, R31, R32, R35, R36 |
NPulse v4 design files
The KiCad project lives in the N-Pulse/ARM-ELEC-CTRL repository on GitHub; these links point at the commit this page was built from.
- LayoutNPulse_v4/NPulse_v4.kicad_pcb
- SchematicNPulse_v4/NPulse_v4.kicad_sch
NPulse v4: common questions
What microcontroller does the NPulse v4 use?
The NPulse v4 is built around the STM32G484METx, from the STM32 family.
How big is the NPulse v4 PCB?
The NPulse v4 measures 39.8 × 72.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the NPulse v4?
157 components, from 27 distinct parts. The full bill of materials is listed on this page.
Where can I download the NPulse v4 design files?
From the N-Pulse/ARM-ELEC-CTRL repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the NPulse v4 design in my own project?
Yes, under the terms of its CC-BY-4.0 license, which N-Pulse chose for the repository.
Can I test firmware for the NPulse v4 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in ARM-ELEC-CTRL
Earlier revisions in the repo: NPulse_v3
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k