My First
Nithin3443·My_First
About the My First PCB
My First is an open source STM32 PCB design by Nithin3443, published on GitHub under the Custom license license. It is a 2-layer board measuring 38 × 32 mm, with 28 components from 16 distinct parts.
Its main chip is the STM32F103C8T6, from the STM32 family. Other key parts include the AMS1117-3.3. By type, the board carries 13 capacitors, 5 resistors, 4 connectors, 2 ICs, 1 crystal and 1 switch.
From the project
Trying to build repository
Main components on the My First
My First bill of materials (BOM)
28 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F103C8T6 | LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | 16MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | USB_B_Micro | USB_Micro-B_Wuerth_629105150521 | J1 |
| 3 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J2, J3, J4 |
| 1 | SW_SPDT | SW_SPDT_PCM12 | SW1 |
| 1 | RED | LED_0603_1608Metric | D1 |
| 1 | 120R | L_0603_1608Metric | FB1 |
| 5 | 100n | C_0402_1005Metric | C1, C2, C3, C4, C9 |
| 1 | 10u | C_0603_1608Metric | C5 |
| 1 | 10n | C_0402_1005Metric | C6 |
| 2 | 1u | C_0402_1005Metric | C7, C8 |
| 2 | 10p | C_0402_1005Metric | C10, C11 |
| 2 | 22u | C_0805_2012Metric | C12, C13 |
| 1 | 10k | R_0402_1005Metric | R1 |
| 4 | 1K5 | R_0402_1005Metric | R2, R3, R4, R5 |
My First design files
The KiCad project lives in the Nithin3443/My_First repository on GitHub; these links point at the commit this page was built from.
- LayoutMy_First.kicad_pcb
- SchematicMy_First.kicad_sch
My First: common questions
What microcontroller does the My First use?
The My First is built around the STM32F103C8T6, from the STM32 family.
How big is the My First PCB?
The My First measures 38 × 32 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the My First?
28 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the My First design files?
From the Nithin3443/My_First repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the My First design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
Can I test firmware for the My First without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k