HardLabs

Uno PH2.0 ExternBoardV3.1

nulllaborg·ph2.0_sensors·others/Uno_PH2.0_ExternBoardV3.1/Uno_PH2.0_ExternBoardV3.1.kicad_pcb

Uno PH2.0 ExternBoardV3.1 PCB layout, top view — open source AVR/Arduino board by nulllaborg
Simulate this board

About the Uno PH2.0 ExternBoardV3.1 PCB

Uno PH2.0 ExternBoardV3.1 is an open source AVR/Arduino PCB design by nulllaborg, published on GitHub. It is a 2-layer board measuring 58.2 × 53.2 mm, with 24 components from 12 distinct parts.

Its main chip is the ArduinoUnoR3, from the AVR/Arduino family. By type, the board carries 19 connectors, 3 jumpers, 1 IC and 1 capacitor.

It belongs with the sensors designs in this gallery.

Main components on the Uno PH2.0 ExternBoardV3.1

ArduinoUnoR3

Uno PH2.0 ExternBoardV3.1 bill of materials (BOM)

24 components, 12 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ArduinoUnoR3
U1
8
Edge_Con3
J1, J2, J4, J5, J7, J8, J10, J11
2
Edge_Con4
J3, J16
2
4pin
J6, J9
2
Edge_Con5
J12, J14
2
Edge_Con6
J13, J15
1
JACK_CAP
J17
2
I2C
J19, J20
1
nRF24L01+
JP1
1
Ultrasoud
JP2
1
Servo*2
JP3
1
10UF
10uF
C1

Uno PH2.0 ExternBoardV3.1 design files

The KiCad project lives in the nulllaborg/ph2.0_sensors repository on GitHub; these links point at the commit this page was built from.

Uno PH2.0 ExternBoardV3.1: common questions

What microcontroller does the Uno PH2.0 ExternBoardV3.1 use?

The Uno PH2.0 ExternBoardV3.1 is built around the ArduinoUnoR3, from the AVR/Arduino family.

How big is the Uno PH2.0 ExternBoardV3.1 PCB?

The Uno PH2.0 ExternBoardV3.1 measures 58.2 × 53.2 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Uno PH2.0 ExternBoardV3.1?

24 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Uno PH2.0 ExternBoardV3.1 design files?

From the nulllaborg/ph2.0_sensors repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Uno PH2.0 ExternBoardV3.1 design in my own project?

The repository has no license, so all rights stay with nulllaborg. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Uno PH2.0 ExternBoardV3.1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in ph2.0_sensors

Similar boards