Valve tester
OlfactoryBehaviorLab·valve_tester·KiCad_Project/valve_tester.kicad_pcb
About the Valve tester PCB
Valve tester is an open source AVR/Arduino PCB design by OlfactoryBehaviorLab, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 81.7 × 58 mm, with 48 components from 16 distinct parts.
Its main chip is the Teensy2.0_(Arduino), from the AVR/Arduino family. Other key parts include the AP2204K-5.0. By type, the board carries 17 resistors, 9 connectors, 8 diodes, 5 switches, 4 transistors and 3 capacitors.
From the project
Small board for actuating solenoids
This repository hosts the code and PCB design files for a small, simple PCB to allow manual testing of solenoid valves
- Manual latching user inputs - Loop mode to allow hands-free cylcing of the valves - Push connect terminals and molex headers for flexibility in attaching the solenoids - Teensy 2.0 programmed with Teensyduino to allow the user to set up patterns of actuation if needed - 24V or 12V input accepted
Main components on the Valve tester
Valve tester bill of materials (BOM)
48 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Teensy2.0_(Arduino) | Teensy2.0 | U1 |
| 1 | AP2204K-5.0 | SOT-23-5 | U2 |
| 4 | PMV40UN2 | SOT-23 | Q1, Q2, Q3, Q4 |
| 1 | Barrel_Jack | BarrelJack_Horizontal | J1 |
| 4 | PHOENIX_5.08MM_TERMINAL Phoenix_5.08mm_Terminal | PHOENIX_1017503 | J2, J3, J4, J5 |
| 4 | 436500228 | MOLEX_436500228 | J6, J7, J8, J9 |
| 4 | SW_Push | SW_1825910-6-4 | SW1, SW2, SW3, SW4 |
| 1 | SW_SPST | SS12D07_CNK | SW5 |
| 4 | SM4007PL | D_SOD-123F | D1, D2, D3, D4 |
| 4 | LED | LED_0603_1608Metric | D5, D6, D7, D8 |
| 1 | 1.0UF 1.0uF | C_0805_2012Metric | C1 |
| 1 | 2.2UF 2.2uF | C_0805_2012Metric | C2 |
| 1 | 0.1UF 0.1uF | C_0805_2012Metric | C3 |
| 9 | 10K | R_0402_1005Metric | R1, R2, R3, R4, R5, R10, R11, R12 +1 |
| 4 | 1K | R_0402_1005Metric | R6, R7, R8, R9 |
| 4 | C25076 100(Ohm) | R_0402_1005Metric | R14, R15, R16, R17 |
Valve tester design files
The KiCad project lives in the OlfactoryBehaviorLab/valve_tester repository on GitHub; these links point at the commit this page was built from.
Valve tester: common questions
What microcontroller does the Valve tester use?
The Valve tester is built around the Teensy2.0_(Arduino), from the AVR/Arduino family.
How big is the Valve tester PCB?
The Valve tester measures 81.7 × 58 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Valve tester?
48 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Valve tester design files?
From the OlfactoryBehaviorLab/valve_tester repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Valve tester design in my own project?
Yes, under the terms of its GPL-3.0 license, which OlfactoryBehaviorLab chose for the repository.
Can I test firmware for the Valve tester without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k