GestureControl

RobbeElsermans·GestureControl·Final Project/PCB V0.3/Gesture Controller/GestureControlV0.3/GestureControl.kicad_pcb

GestureControl PCB layout, top view — open source STM32 board by RobbeElsermans

About the GestureControl PCB

GestureControl is an open source STM32 PCB design by RobbeElsermans, published on GitHub under the MIT license. It is a 4-layer board measuring 254.1 × 81.6 mm, with 132 components from 46 distinct parts.

Its main chip is the STM32L151RETx, from the STM32 family. Other key parts include the AP5100_3.3, VL53L3CXV0DH_1 and STM32F401RETx. By type, the board carries 51 capacitors, 38 resistors, 18 connectors, 9 ICs, 8 diodes and 2 crystals.

It belongs with the sensors designs in this gallery.

From the project

Gesture control with ToF sensor

Gesture controlling with X-NUCLEO-53L3A2 DevKit.

Main components on the GestureControl

AP5100_3.3VL53L3CXV0DH_1STM32L151RETxSTM32F401RETx

GestureControl bill of materials (BOM)

132 components, 46 distinct parts.

QtyPartRefs
2
AP5100_3.3
U1, U2
5
VL53L3CXV0DH_1
U3, U4, U5, U8, U9
1
STM32L151RETx
U6
1
STM32F401RETx
U7
1
8MHz
Y1
1
32kHz
Y2
1
Conn_01x04_I2I-LCD
J1
1
BATT
J2
1
FTDI
J7
1
Conn_01x06
J8
1
UART
J9
1
EXTERN I2C
J10
2
Conn_01x02
J11, J12
8
WR-MM Female SMT Connector
J13, J14, J15, J16, J20, J21, J22, J23
2
Conn_02x19_Odd_Even
J24, J25
2
SolderJumper_3_Open
JP2, JP3
1
SW1
SW1
1
SW2
SW2
1
L1
D1
1
L2
D2
Show 26 more
QtyPartRefs
1
L3
D3
1
L4
D4
1
L5
D5
1
1N4002
D6
2
B230A
D7, D8
2
10µH
L1, L2
20
100n
C1, C2, C8, C9, C14, C15, C16, C20 +12
2
10µF
C3, C4
2
100nF
C5, C6
2
10µ
C7, C43
7
4.7µ
C10, C32, C33, C36, C37, C38, C47
2
4.7µF
C11, C12
7
10µ
C13, C34, C39, C40, C41, C42, C45
2
20p
C17, C18
2
20p
C19, C22
1
1µ
C30
4
x
C48, C49, C50, C51
9
100
R1, R2, R3, R4, R5, R8, R9, R23 +1
14
10k
R6, R7, R12, R13, R16, R17, R20, R26 +6
4
4k7
R10, R11, R21, R22
2
100k
R14, R15
1
220
R18
1
820
R19
1
18k
R25
2
56k
R27, R28
4
x
R35, R36, R37, R38

GestureControl design files

The KiCad project lives in the RobbeElsermans/GestureControl repository on GitHub; these links point at the commit this page was built from.

GestureControl: common questions

What microcontroller does the GestureControl use?

The GestureControl is built around the STM32L151RETx, from the STM32 family.

How big is the GestureControl PCB?

The GestureControl measures 254.1 × 81.6 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the GestureControl?

132 components, from 46 distinct parts. The full bill of materials is listed on this page.

Where can I download the GestureControl design files?

From the RobbeElsermans/GestureControl repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the GestureControl design in my own project?

Yes, under the terms of its MIT license, which RobbeElsermans chose for the repository.

Can I test firmware for the GestureControl without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards