Slug v1.0
rumbletech·Slug_v1.0·kicad/prj/slug_v1_0.kicad_pcb
About the Slug v1.0 PCB
Slug v1.0 is an open source STM32 PCB design by rumbletech, published on GitHub under the MIT license. It is a 4-layer board measuring 60 × 35 mm, with 78 components from 26 distinct parts.
Its main chip is the STM32F103C8TX, from the STM32 family. Other key parts include the AMS1117-3.3 and TXB0102DCT. By type, the board carries 30 resistors, 20 capacitors, 11 diodes, 7 connectors, 5 ICs and 2 crystals.
From the project
Slug ( Slog/Serial Logger ) is an open source firmware and an open source hardware project , it implements logging of serial buses like USART,I2C,SPI to an SD Card.
Main components on the Slug v1.0
Slug v1.0 bill of materials (BOM)
78 components, 26 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F103C8TX STM32F103C8Tx | LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 3 | TXB0102DCT | TSSOP-8_3x3mm_P0.65mm | U3, U4, U5 |
| 1 | 8MHZ 11.0592MHz | Crystal_SMD_7050-4Pin_7.0x5.0mm | X1 |
| 1 | 32.768K | Crystal_SMD_SeikoEpson_MC306-4Pin_8.0x3.2mm | Y2 |
| 1 | Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | Conn_01x03_Pin | PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | C505111 USB_B_Micro | USB_Micro-B_Amphenol_10118193-0001LF_Horizontal | J4 |
| 3 | Conn_01x03_Pin | PinHeader_1x03_P2.54mm_Horizontal | J5, J6, J7 |
| 1 | TF-CARD H1.8 TF-CARD_H1.8 | TFCARDH18 | J8 |
| 1 | SW_SPDT | SW_SPDT_CK_JS102011SAQN | SW4 |
| 1 | C202424 SW_SPST | SW_SPST_SKQG_WithStem | SW5 |
| 1 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1 |
| 10 | LED | LED_0805_2012Metric | D2, D3, D4, D5, D6, D7, D8, D9 +2 |
| 1 | 50R100MHZ 50R100MHz | L_0805_2012Metric | FB1 |
| 12 | 0.1UF 0.1uF | C_0805_2012Metric | C1, C2, C3, C4, C6, C7, C15, C16 +4 |
| 1 | 1UF 1uF | C_0805_2012Metric | C5 |
| 2 | 20PF 20pF | C_0805_2012Metric | C8, C9 |
| 2 | 10UF 22uF | C_0805_2012Metric | C10, C11 |
| 1 | 10NF 10nF | C_0805_2012Metric | C12 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 0.1UF 100nF | C_0805_2012Metric | C13 |
| 1 | 0.1uF | C_0805_2012Metric | C14 |
| 6 | 10K | R_0805_2012Metric | R1, R2, R3, R13, R19, R24 |
| 13 | 22R | R_0805_2012Metric | R4, R5, R6, R7, R8, R9, R10, R16 +5 |
| 1 | 1.5K 1.5k | R_0805_2012Metric | R11 |
| 10 | 2.2K | R_0805_2012Metric | R14, R15, R18, R20, R23, R25, R28, R29 +2 |
Slug v1.0 design files
The KiCad project lives in the rumbletech/Slug_v1.0 repository on GitHub; these links point at the commit this page was built from.
Slug v1.0: common questions
What microcontroller does the Slug v1.0 use?
The Slug v1.0 is built around the STM32F103C8TX, from the STM32 family.
How big is the Slug v1.0 PCB?
The Slug v1.0 measures 60 × 35 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Slug v1.0?
78 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Slug v1.0 design files?
From the rumbletech/Slug_v1.0 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Slug v1.0 design in my own project?
Yes, under the terms of its MIT license, which rumbletech chose for the repository.
Can I test firmware for the Slug v1.0 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k