TeensyWheel
sdalimon·TeensyWheel
About the TeensyWheel PCB
TeensyWheel is an open source PCB design by sdalimon, published on GitHub. It is a 4-layer board measuring 80.7 × 62.9 mm, with 39 components from 15 distinct parts.
Other key parts include the DEV-16771. By type, the board carries 14 switches, 8 resistors, 6 connectors, 6 capacitors, 2 diodes and 1 IC.
From the project
A replacement PCB for the Flashfire ForceWheel WH2304-V gaming wheel
I bought the Flashfire ForceWheel WH2304-V because it was low cost, but found the button configuration annoying. There are a lot of buttons, but many of them are shared with other functions (like the paddles and gearshift) leaving few usable ones. Some of this was configurable, but it had to be done each time the unit was plugged in.
I knew a Teensy can act as a joystick so looked into using one as a replacement controller. It didn't turn out that hard. Most of the time was spent measuring the button and mounting hole locations on the original PCB to be sure the replecement would fit.
Main components on the TeensyWheel
TeensyWheel bill of materials (BOM)
39 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DEV-16771 | MODULE_DEV-16771 | U1 |
| 1 | FFB2222A | SOT-363_SC-70-6 | Q1 |
| 1 | Conn_01x03_Male | JST_EH_B3B-EH-A_1x03_P2.50mm_Vertical | J1 |
| 2 | Conn_01x04_Male | JST_EH_B4B-EH-A_1x04_P2.50mm_Vertical | J2, J6 |
| 1 | Conn_01x11_Male | JST_PH_B11B-PH-K_1x11_P2.00mm_Vertical | J3 |
| 2 | Conn_01x05_Male | JST_EH_B5B-EH-A_1x05_P2.50mm_Vertical | J4, J5 |
| 13 | PAD | Sw_PAD_6.5mm | SW1, SW2, SW3, SW4, SW6, SW7, SW8, SW9 +5 |
| 1 | SW_DP3T | Sense_Sw | SW5 |
| 1 | LED_Dual_KAK | LED_D3.0mm-3 | D1 |
| 1 | BAT54A | SOT-23 | D2 |
| 1 | FerriteBead | L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | FB1 |
| 3 | 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C6 |
| 3 | 10u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4, C5 |
| 6 | 1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R5, R6 |
| 2 | 330 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R8 |
TeensyWheel design files
The KiCad project lives in the sdalimon/TeensyWheel repository on GitHub; these links point at the commit this page was built from.
- LayoutTeensyWheel.kicad_pcb
- SchematicTeensyWheel.kicad_sch
TeensyWheel: common questions
How big is the TeensyWheel PCB?
The TeensyWheel measures 80.7 × 62.9 mm, has 4 copper layers and is 1.25 mm thick.
How many components are on the TeensyWheel?
39 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the TeensyWheel design files?
From the sdalimon/TeensyWheel repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the TeensyWheel design in my own project?
The repository has no license, so all rights stay with sdalimon. Use it as a reference, and ask the author before reusing the design.