HardLabs

Blackmagic pikim clone

sergiomd4·blackmagic-pikim-clone·Hardware/blackmagic_richardeoin.kicad_pcb

Blackmagic pikim clone PCB layout, top view — open source STM32 board by sergiomd4

About the Blackmagic pikim clone PCB

Blackmagic pikim clone is an open source STM32 PCB design by sergiomd4, published on GitHub under the CC0-1.0 license. It is a 2-layer board measuring 41 × 17 mm, with 39 components from 21 distinct parts.

Its main chip is the STM32F_48PIN, from the STM32 family. Other key parts include the TXS0108 and TLV70033DCK. By type, the board carries 13 resistors, 11 capacitors, 4 ICs, 4 diodes, 2 jumpers and 1 transistor.

From the project

Board focused on embedded microcontrollers debugging

Black Magic Pikim Clone ========================================

Pikim is a version of the Black Magic Mini board.

It is an easy-to-use board used for debugging embedded microcontrollers. It supports several targets from manufacturers such as STMicroelectronics, Atmel, Nordic Semiconductor, NXP, Texas Instruments, Freescale, Silicon Labs, Xilinx or Raspberry Pi.

Main components on the Blackmagic pikim clone

STM32F_48PINTXS0108TLV70033DCK

Blackmagic pikim clone bill of materials (BOM)

39 components, 21 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32F_48PIN
IC1
1
TXS0108
IC2
1
TLV70033DCK
IC3
1
—
U$32
1
IRLML5103
Q1
1
8MHz
Y1
1
—
CN1
2
OMRON_SPST.B3U-1000P(M)
BTN1, BTN2
1
—
JP1
1
—
JP2
1
GREEN
D1
1
RED
D2
2
YELLOW
D3, D4
2
1uF
C1, C2
7
100nF
C3, C4, C5, C6, C9, C10, C11
2
18pF
C7, C8
2
22Ω
R1, R2
1
1K5
R3
4
10K
R4, R6, R7, R9
2
4K7
R5, R8
Show 1 more
QtyPartRefs
4
390Ω
R10, R11, R12, R13

Blackmagic pikim clone design files

The KiCad project lives in the sergiomd4/blackmagic-pikim-clone repository on GitHub; these links point at the commit this page was built from.

Blackmagic pikim clone: common questions

What microcontroller does the Blackmagic pikim clone use?

The Blackmagic pikim clone is built around the STM32F_48PIN, from the STM32 family.

How big is the Blackmagic pikim clone PCB?

The Blackmagic pikim clone measures 41 × 17 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Blackmagic pikim clone?

39 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Blackmagic pikim clone design files?

From the sergiomd4/blackmagic-pikim-clone repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Blackmagic pikim clone design in my own project?

Yes, under the terms of its CC0-1.0 license, which sergiomd4 chose for the repository.

Can I test firmware for the Blackmagic pikim clone without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards