STM32-PCB-Design
Shadaab1904·STM32-PCB-Design
About the STM32-PCB-Design
STM32-PCB-Design is an open source STM32 PCB design by Shadaab1904, published on GitHub under the MIT license. It is a 2-layer board measuring 44 × 38.7 mm, with 27 components from 15 distinct parts.
Its main chip is the STM32F103C8T6, from the STM32 family. Other key parts include the AMS1117-3.3. By type, the board carries 13 capacitors, 5 resistors, 4 connectors, 2 ICs, 1 crystal and 1 diode.
From the project
KiCad project: STM32 PCB Design on STM32F103C8T6
- STM32F103C8T6: ARM Cortex-M3 microcontroller (Blue Pill) - USBBMicro: USB Micro-B connector for programming/power - AMS1117-3.3: Voltage regulator (3.3V output) - Crystal: External crystal oscillator with GND pads - FB: FerriteBead: Noise filter on power rail - LED: Status or debug indicator - Resistor: For LED and pull-up/down functions - Capacitor: Decoupling and oscillator loading - Conn01x04Pin: 4-pin GPIO header - MountingHoles: Mechanical support for enclosure/PCB mount
Main components on the STM32-PCB-Design
STM32-PCB-Design bill of materials (BOM)
27 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | STM32F103C8T6 | LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | 16MHZ | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | USB_B_Micro | USB_Micro-B_Wuerth_629105150521 | J1 |
| 3 | CONN_01X04_PIN Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J2, J3, J4 |
| 1 | RED | LED_0603_1608Metric | D1 |
| 1 | 120R | L_0603_1608Metric | FB1 |
| 2 | 22U 22u | C_0805_2012Metric | C1, C2 |
| 1 | 10U 10u | C_0603_1608Metric | C3 |
| 5 | 100N 100n | C_0402_1005Metric | C4, C5, C6, C7, C11 |
| 1 | 10N 10n | C_0402_1005Metric | C8 |
| 2 | 1u | C_0402_1005Metric | C9, C10 |
| 2 | 10P 10p | C_0402_1005Metric | C12, C13 |
| 4 | 1K5 | R_0402_1005Metric | R1, R3, R4, R5 |
| 1 | 10K | R_0402_1005Metric | R2 |
STM32-PCB-Design design files
The KiCad project lives in the Shadaab1904/STM32-PCB-Design repository on GitHub; these links point at the commit this page was built from.
- LayoutMy_STM32_Board.kicad_pcb
- SchematicMy_STM32_Board.kicad_sch
- BOMMy_STM32_Board_BOM.csv
STM32-PCB-Design: common questions
What microcontroller does the STM32-PCB-Design use?
The STM32-PCB-Design is built around the STM32F103C8T6, from the STM32 family.
How big is the STM32-PCB-Design?
The STM32-PCB-Design measures 44 × 38.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the STM32-PCB-Design?
27 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the STM32-PCB-Design design files?
From the Shadaab1904/STM32-PCB-Design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the STM32-PCB-Design design in my own project?
Yes, under the terms of its MIT license, which Shadaab1904 chose for the repository.
Can I test firmware for the STM32-PCB-Design without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k