STM32WB55CEU6-Bluetooth-Hardware-Design

Shadaab1904·STM32WB55CEU6-Bluetooth-Hardware-Design

STM32WB55CEU6-Bluetooth-Hardware-Design PCB layout, top view — open source STM32 board by Shadaab1904

About the STM32WB55CEU6-Bluetooth-Hardware-Design PCB

STM32WB55CEU6-Bluetooth-Hardware-Design is an open source STM32 PCB design by Shadaab1904, published on GitHub under the MIT license. It is a 4-layer board measuring 55 × 32 mm, with 40 components from 21 distinct parts.

Its main chip is the STM32WB55CEU6, from the STM32 family. Other key parts include the MIC5365-3.3YD5. By type, the board carries 19 capacitors, 7 resistors, 3 connectors, 3 inductors, 2 ICs and 2 crystals.

It belongs with the iot & wireless designs in this gallery.

From the project

This repository contains the end-to-end hardware design of a custom PCB based on the STM32WB55CEU6 microcontroller. The project was developed using KiCad 9.0 for schematic and PCB design, and STM32CubeIDE for pin mapping and configuration. The design integrates MCU, RF, power man

This repository contains the end-to-end hardware design of a custom PCB based on the STM32WB55CEU6 microcontroller. The project was developed using KiCad 9.0 for schematic and PCB design, and STM32CubeIDE for pin mapping and configuration. The design integrates MCU, RF, power management, USB, and peripherals, and follows high-speed and RF hardware design best practices.

Main components on the STM32WB55CEU6-Bluetooth-Hardware-Design

STM32WB55CEU6-Bluetooth-Hardware-Design bill of materials (BOM)

40 components, 21 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
MIC5365-3.3YD5
Microchip Technology
U1
1
STM32WB55CEU6
STMicroelectronics
U2
1
32.768 kHz
NDK
X1
1
32MHZ
32MHz
NDK
X2
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
GCT
J1
1
CONN_01X04
Conn_01x04
MOLEX
J2
1
Conn_Coaxial
Hirose Connector
J4
1
DLF162500LT-5028A1
TDK
FLT1
1
SW_Push
C&K
SW1
1
USBLC6-2SC6
STMicroelectronics
D1
1
LED
Wurth Elektronik
D2
1
10NH
10nH
Murata Electronics
L1
1
10UH
10uH
Murata Electronics
L2
1
2.7NH
2.7nH
Murata Electronics
L3
5
4.7UF
4.7uF
KYOCERA AVX
C1, C2, C3, C10, C14
10
100NF
100nF
KYOCERA AVX
C4, C5, C6, C7, C8, C9, C11, C12 +2
1
0.8PF
0.8pF
Murata Electronics
C15
1
0.3PF
0.3pF
Murata Electronics
C16
2
10PF
10pF
KYOCERA AVX
C17, C18
3
5.1K
YAGEO
R1, R2, R6
Show 1 more
QtyPartRefs
4
220R
YAGEO
R3, R4, R5, R7

STM32WB55CEU6-Bluetooth-Hardware-Design design files

The KiCad project lives in the Shadaab1904/STM32WB55CEU6-Bluetooth-Hardware-Design repository on GitHub; these links point at the commit this page was built from.

STM32WB55CEU6-Bluetooth-Hardware-Design: common questions

What microcontroller does the STM32WB55CEU6-Bluetooth-Hardware-Design use?

The STM32WB55CEU6-Bluetooth-Hardware-Design is built around the STM32WB55CEU6, from the STM32 family.

How big is the STM32WB55CEU6-Bluetooth-Hardware-Design PCB?

The STM32WB55CEU6-Bluetooth-Hardware-Design measures 55 × 32 mm, has 4 copper layers and is 1.58 mm thick.

How many components are on the STM32WB55CEU6-Bluetooth-Hardware-Design?

40 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the STM32WB55CEU6-Bluetooth-Hardware-Design design files?

From the Shadaab1904/STM32WB55CEU6-Bluetooth-Hardware-Design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the STM32WB55CEU6-Bluetooth-Hardware-Design design in my own project?

Yes, under the terms of its MIT license, which Shadaab1904 chose for the repository.

Can I test firmware for the STM32WB55CEU6-Bluetooth-Hardware-Design without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards