Driver boostcon
About the Driver boostcon PCB
Driver boostcon is an open source AVR/Arduino PCB design by sjaxel, published on GitHub. It is a 2-layer board measuring 100 × 80 mm, with 57 components from 33 distinct parts.
Its main chip is the ATMEGA328P-PU, from the AVR/Arduino family. Other key parts include the INA282. By type, the board carries 26 capacitors, 15 resistors, 2 ICs, 2 transistors, 2 connectors and 2 inductors.
Main components on the Driver boostcon
Driver boostcon bill of materials (BOM)
57 components, 33 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATMEGA328P-PU | DIP-28_W7.62mm_Socket | U601 |
| 1 | INA282 | SOIC-8_3.9x4.9mm_Pitch1.27mm | U801 |
| 1 | IRF4905S | TO-263-3Lead_NoPin2 | Q401 |
| 1 | BSC016N04LS | PG-TDSON-8 | Q402 |
| 1 | 16 MHz | Crystal_SMD_4.6mmx11.2mm | Y601 |
| 1 | On Switch | Socket_Strip_Straight_1x04_Pitch2.54mm | P301 |
| 1 | Programmer | Pin_Header_Straight_2x03_Pitch2.54mm | P601 |
| 1 | Fuse | Littlefuse_30mm_M5 | F301 |
| 2 | SwitchDriver | SOT-23-5 | FDR501, FDR502 |
| 1 | NCP5501 | TO-263-3Lead_TabPin4 | LDO201 |
| 1 | SW_Push | Button_SMD_6x6mm | SW601 |
| 1 | DS75 | SOIC-8_3.9x4.9mm_Pitch1.27mm | TS701 |
| 1 | D_Schottky | TO220AB-SMD | D401 |
| 1 | INDUCTOR | SER2900 | L401 |
| 1 | 80 uH | Chipdrossel | L601 |
| 1 | 10 uF | CP_Elec_6.3x5.3 | C201 |
| 9 | 100 nF | C_0603_CustomText | C202, C501, C502, C601, C602, C603, C607, C701 +1 |
| 1 | 4.7 uF | C_0805_CustomText | C203 |
| 1 | 100 nF | C_0805_CustomText | C204 |
| 3 | 470 uF | CP_Elec_10x10.5 | C401, C404, C405 |
Show 13 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 6 | 1 uF | C_0805_CustomText | C402, C403, C406, C503, C504, C606 |
| 2 | 20 pF | C_0603_CustomText | C604, C605 |
| 1 | C_Small | C_0603_CustomText | C801 |
| 2 | 680 nF | C_0603_CustomText | C802, C803 |
| 1 | 2k Ohm | C_0603_CustomText | R401 |
| 1 | 5 Ohm | C_0603_CustomText | R402 |
| 3 | 0.002 Ohm | R-SMD-4527 | R403, R404, R405 |
| 2 | 100 Ohm | C_0603_CustomText | R601, R602 |
| 1 | 10k Ohm | C_0603_CustomText | R603 |
| 2 | 4.7k | C_0603_CustomText | R604, R605 |
| 2 | 4.7 kOhm | C_0603_CustomText | R606, R607 |
| 2 | 6k | R_0603_CustomText | R801, R802 |
| 1 | 47k | C_0603_CustomText | R901 |
Driver boostcon design files
The KiCad project lives in the sjaxel/driver-boostcon repository on GitHub; these links point at the commit this page was built from.
Driver boostcon: common questions
What microcontroller does the Driver boostcon use?
The Driver boostcon is built around the ATMEGA328P-PU, from the AVR/Arduino family.
How big is the Driver boostcon PCB?
The Driver boostcon measures 100 × 80 mm, has 2 copper layers and is 1.5 mm thick.
How many components are on the Driver boostcon?
57 components, from 33 distinct parts. The full bill of materials is listed on this page.
Where can I download the Driver boostcon design files?
From the sjaxel/driver-boostcon repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Driver boostcon design in my own project?
The repository has no license, so all rights stay with sjaxel. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Driver boostcon without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/ArduinoMagspoof
samyk
35 × 29 mm11 parts2LNo license4.2k
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoLabrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2k
AVR/ArduinoModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoV4
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k