Mainboard
Sprudlwassr·CrazyCart_Systemanzeige·PCB/mainboard/mainboard.kicad_pcb
About the Mainboard PCB
Mainboard is an open source AVR/Arduino PCB design by Sprudlwassr, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 45.2 × 43.6 mm, with 30 components from 18 distinct parts.
Its main chip is the ATmega8-16A, from the AVR/Arduino family. By type, the board carries 13 resistors, 8 capacitors, 4 connectors, 1 IC, 1 crystal and 1 switch.
Main components on the Mainboard
Mainboard bill of materials (BOM)
30 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATmega8-16A | TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | 16MHz | Crystal_SMD_ECS_CSM3X-2Pin_7.6x4.1mm | Y1 |
| 1 | VBuck | PinSocket_1x03_P2.54mm_Vertical | J1 |
| 1 | Temp | PinSocket_1x03_P2.54mm_Horizontal | J2 |
| 1 | Hall | PinSocket_1x03_P2.54mm_Horizontal | J3 |
| 1 | Display | PinSocket_1x16_P2.54mm_Vertical | J4 |
| 1 | Poti | Potentiometer_Bourns_3314G_Vertical | RV1 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 1 | D | D_0805_2012Metric | D1 |
| 2 | 22pF | C_0805_2012Metric | C1, C2 |
| 2 | 100nF | C_0805_2012Metric | C3, C4 |
| 2 | 100µF | CP_Elec_5x5.8 | C5, C6 |
| 2 | 10nF | C_0603_1608Metric | C7, C8 |
| 1 | 99k | R_0805_2012Metric | R1 |
| 1 | 11k | R_0805_2012Metric | R2 |
| 3 | 10k | R_0805_2012Metric | R3, R5, R7 |
| 1 | 4.7k | R_0805_2012Metric | R4 |
| 7 | 0 | R_0805_2012Metric | R6, R8, R9, R10, R11, R12, R13 |
Mainboard design files
The KiCad project lives in the Sprudlwassr/CrazyCart_Systemanzeige repository on GitHub; these links point at the commit this page was built from.
Mainboard: common questions
What microcontroller does the Mainboard use?
The Mainboard is built around the ATmega8-16A, from the AVR/Arduino family.
How big is the Mainboard PCB?
The Mainboard measures 45.2 × 43.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Mainboard?
30 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the Mainboard design files?
From the Sprudlwassr/CrazyCart_Systemanzeige repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Mainboard design in my own project?
Yes, under the terms of its GPL-3.0 license, which Sprudlwassr chose for the repository.
Can I test firmware for the Mainboard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in CrazyCart_Systemanzeige
Similar boards
AVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0kAVR/Arduino
Megadesk
gcormier
41.7 × 32.2 mm23 parts2LGPL-3.0818AVR/Arduino
Easyduino Atmega Nano
Hanqaqa
43.4 × 18 mm30 parts4LCERN-OHL-P-2.0746