Watering project 2
TeaGuardian·watering_project_2·схемы/wsr2/wsr2.kicad_pcb
About the Watering project 2 PCB
Watering project 2 is an open source STM32 PCB design by TeaGuardian, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 111.8 × 53.3 mm, with 24 components from 10 distinct parts.
Its main chip is the YAAJ_BluePill, from the STM32 family. By type, the board carries 12 connectors, 5 resistors, 3 transistors, 2 diodes, 1 IC and 1 speaker.
Main components on the Watering project 2
Watering project 2 bill of materials (BOM)
24 components, 10 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | YAAJ_BluePill | U1 | |
| 3 | NMOS | Q1, Q2, Q3 | |
| 3 | load (valve) con | J1, J4, J5 | |
| 2 | uart | J2, J3 | |
| 2 | rele | J6, J12 | |
| 1 | servo | J7 | |
| 4 | analog sensor | J8, J9, J10, J11 | |
| 1 | Speaker | LS1 | |
| 2 | LED | D1, D2 | |
| 5 | R | R1, R2, R3, R4, R5 |
Watering project 2 design files
The KiCad project lives in the TeaGuardian/watering_project_2 repository on GitHub; these links point at the commit this page was built from.
- Layoutсхемы/wsr2/wsr2.kicad_pcb
- Schematicсхемы/wsr2/wsr2.kicad_sch
Watering project 2: common questions
What microcontroller does the Watering project 2 use?
The Watering project 2 is built around the YAAJ_BluePill, from the STM32 family.
How big is the Watering project 2 PCB?
The Watering project 2 measures 111.8 × 53.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Watering project 2?
24 components, from 10 distinct parts. The full bill of materials is listed on this page.
Where can I download the Watering project 2 design files?
From the TeaGuardian/watering_project_2 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Watering project 2 design in my own project?
Yes, under the terms of its Apache-2.0 license, which TeaGuardian chose for the repository.
Can I test firmware for the Watering project 2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k