11 open source boards using the YAAJ_BluePill

Real designs built with the YAAJ_BluePill, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

11 boardsClear filters|Most starred

How designs wire the YAAJ_BluePill

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the YAAJ_BluePill connects to, and the resistors, capacitors and other passives placed on it.

  • The VBAT pin is left unconnected on 6 of 6 designs.
  • The PC13 pin is left unconnected on 6 of 6 designs.
  • The PC14 pin is left unconnected on 6 of 6 designs.
  • The PC15 pin is left unconnected on 6 of 6 designs.
PA8pin 5Connected to: Not connected 67% · a signal 33%
PA11pin 8Connected to: Not connected 83% · a signal 17%
PA12pin 9Connected to: Not connected 83% · a signal 17%
PA15pin 10Connected to: Not connected 67% · a signal 33%
GNDpin 19, 39, 40Connected to: GND 72% · not connected 17%
3V3pin 20, 38Connected to: 3.3V 75% · not connected 25%
VBATpin 21Connected to: Not connected 100%
PC13pin 22Connected to: Not connected 100%
PC14pin 23Connected to: Not connected 100%
PC15pin 24Connected to: Not connected 100%
RSTpin 37Connected to: Not connected 67% · a signal 33%

26 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Bluepill design by thesunRider, ADCS by Amr-H25, MasterModule by dmitry131131 and TAILS by Mario-dango.

The YAAJ_BluePill in open source designs

The gallery holds 11 open source boards using the YAAJ_BluePill from 8 GitHub repositories; a typical one measures about 78.4 × 65.2 mm and carries around 22 components.

100% are two-layer designs, the rest use four layers or more, and 18% carry an open source license.

The most starred is Bluepill design by thesunRider.

Parts used alongside the YAAJ_BluePill

Microcontrollers on boards using the YAAJ_BluePill

YAAJ_BluePill: common questions

Where can I find a YAAJ_BluePill reference design?

Each of the 11 boards on this page is a real design using the YAAJ_BluePill. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the YAAJ_BluePill VBAT pin connected?

The VBAT pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the YAAJ_BluePill.

How is the YAAJ_BluePill PC13 pin connected?

The PC13 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the YAAJ_BluePill.

How is the YAAJ_BluePill PC14 pin connected?

The PC14 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the YAAJ_BluePill.

Which microcontrollers do boards using the YAAJ_BluePill use?

Most are built on STM32 (3), AVR/Arduino (1), ESP32 (1) and Raspberry Pi (1).

How big is a typical board using the YAAJ_BluePill?

The median is 78.4 × 65.2 mm, and 100% are two-layer designs.

What is the most popular open source board using the YAAJ_BluePill?

By GitHub stars, Bluepill design by thesunRider, with 3 stars.

Can I simulate one of these boards using the YAAJ_BluePill before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part