Agp power monitor
TeHSiGGi·agp-power-monitor·hardware/apm.kicad_pcb
About the Agp power monitor PCB
Agp power monitor is an open source STM32 PCB design by TeHSiGGi, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 115 × 76.3 mm, with 119 components from 37 distinct parts.
Its main chip is the STM32F103C6TX, from the STM32 family. Other key parts include the INA3221 and MCP1703AX-330XXTT. By type, the board carries 46 capacitors, 38 resistors, 21 connectors, 6 diodes, 5 ICs and 2 crystals.
From the project
Power minitoring utility for AGP graphics cards
The AGP Power Monitor is uses a custom AGP riser card to measure and monitor power consumption of AGP cards. It provides real-time voltage and current measurements for the various power rails used by AGP graphics cards, allowing for detailed power analysis and troubleshooting.
- AGP Connectors: Edge connector for AGP cards and slot connector for motherboard interface - Power Measurement: INA3221 triple-channel power monitors for measuring voltage and current - Microcontroller: STM32F103C8T6 MCU for data processing and USB communication - Power Supply: All logic is powered via the USB input -…
Main components on the Agp power monitor
Agp power monitor bill of materials (BOM)
119 components, 37 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | INA3221 | Texas_RGV0016A_VQFN-16-1EP_4x4mm_P0.65mm_EP2.1x2.1mm | U401, U402, U403 |
| 1 | MCP1703AX-330XXTT MCP1703Ax-330xxTT | SOT-23 | U501 |
| 1 | STM32F103C6TX STM32F103C6Tx | LQFP-48_7x7mm_P0.5mm | U502 |
| 1 | 8MHZ 8MHz | Crystal_HC49-U_Vertical | Y501 |
| 1 | 32.768KHZ 32.768kHz | Crystal_DS10_D1.0mm_L4.3mm_Horizontal | Y502 |
| 1 | ~ | edge_universal | J201 |
| 1 | 145376-2 | Conn_AMP_1MM_STD_EDGE_132_POS_145376-2 | J202 |
| 2 | 12V_PROBE | PinHeader_1x02_P2.54mm_Vertical | J203, J208 |
| 2 | 3.3V_PROBE | PinHeader_1x02_P2.54mm_Vertical | J204, J209 |
| 2 | VDDQ_PROBE | PinHeader_1x02_P2.54mm_Vertical | J205, J210 |
| 2 | 5V_PROBE | PinHeader_1x02_P2.54mm_Vertical | J206, J211 |
| 2 | GND_PROBE | PinHeader_1x02_P2.54mm_Vertical | J207, J212 |
| 2 | 39301060 | Molex_Mini-Fit_Jr_5569-06A2_2x03_P4.20mm_Horizontal | J301, J302 |
| 2 | 641737-1 | 641737-1 | J303, J304 |
| 2 | SCREW_TERMINAL_01X02 Screw_Terminal_01x02 | TerminalBlock_RND_205-00232_1x02_P5.08mm_Horizontal | J305, J306 |
| 1 | USB_B_Mini | USB_Mini-B_Wuerth_65100516121_Horizontal | J501 |
| 1 | I2C | PinHeader_1x04_P2.54mm_Vertical | J502 |
| 1 | STLink | PinHeader_1x04_P2.54mm_Vertical | J503 |
| 1 | 200MA 200mA | Fuse_1812_4532Metric | F501 |
| 2 | PRTR5V0U2X | SOT-143 | D501, D503 |
Show 17 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | P4SMAJ5.0A | D_SMA | D502 |
| 3 | LED | LED_1206_3216Metric | D504, D505, D506 |
| 2 | 4µ7 | C_1206_3216Metric | C201, C207 |
| 12 | 22µ | C_1206_3216Metric | C202, C203, C204, C205, C206, C208, C209, C210 +4 |
| 10 | 1µ | C_0603_1608Metric | C301, C302, C303, C304, C305, C306, C307, C308 +2 |
| 16 | 100N 100n | C_0603_1608Metric | C401, C402, C403, C404, C405, C406, C407, C408 +8 |
| 1 | 10µ | C_1206_3216Metric | C503 |
| 4 | 20P 20p | C_0603_1608Metric | C508, C509, C510, C511 |
| 1 | 10N 10n | C_0603_1608Metric | C512 |
| 9 | 0R01 | R_2816_7142Metric | R401, R402, R403, R404, R405, R406, R407, R408 +1 |
| 18 | 10 | R_0603_1608Metric | R410, R411, R412, R413, R414, R415, R416, R417 +10 |
| 2 | 22 | R_0603_1608Metric | R501, R502 |
| 1 | 1M | R_0603_1608Metric | R503 |
| 1 | 10K 10k | R_0603_1608Metric | R504 |
| 1 | 4K7 4k7 | R_0603_1608Metric | R505 |
| 3 | 3K3 3k3 | R_0603_1608Metric | R506, R507, R511 |
| 3 | 220 | R_0603_1608Metric | R508, R509, R510 |
Agp power monitor design files
The KiCad project lives in the TeHSiGGi/agp-power-monitor repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/apm.kicad_pcb
- Schematichardware/apm.kicad_sch
- BOMhardware/apm.csv
Agp power monitor: common questions
What microcontroller does the Agp power monitor use?
The Agp power monitor is built around the STM32F103C6TX, from the STM32 family.
How big is the Agp power monitor PCB?
The Agp power monitor measures 115 × 76.3 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Agp power monitor?
119 components, from 37 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Agp power monitor design files?
From the TeHSiGGi/agp-power-monitor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Agp power monitor design in my own project?
Yes, under the terms of its GPL-3.0 license, which TeHSiGGi chose for the repository.
Can I test firmware for the Agp power monitor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k