35 open source boards using the INA3221
Real designs built with the INA3221, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Glider
Modos-Labs
90 × 80 mm356 parts4LCERN-OHL-S-2.02.7kSTM32
Orion - Control Board
AshishA26
70 × 82.4 mm69 parts2LNo license253AVR/Arduino
TougherPowerMonitor-HW
ahillbom
130 × 53 mm75 parts2LMIT18RISC-V
Kepler x
kunichiko
144 × 150 mm153 parts4LMIT4ESP32
Hand main
SonDinh23
70 × 45 mm105 parts4LGPL-3.04SNAP Power Controller
jaisor
52 × 29 mm37 parts2LCERN-OHL-P-2.04ESP32
Bench psu monitor
fixthepixel
110 × 80 mm35 parts2LCustom license4STM32
Agp power monitor
TeHSiGGi
115 × 76.3 mm119 parts4LGPL-3.02Lichtenprog
cr1tbit
28 × 28 mm69 parts4LCERN-OHL-P-2.02STM32
Mini pd psu
ManhTi3012
60 × 50 mm66 parts2LMIT2Tinynode
Stary2001
80 × 60 mm63 parts4LCERN-OHL-P-2.02STM32
Satnogs comms
PeakSat
90.2 × 95.9 mm273 parts6LCERN-OHL-1.21Meshtastic node
benkyd
150 × 50 mm110 parts4LNo license1Kubisat power v2
gredzikk
80 × 80 mm77 parts2LMIT1ESP32
Lora pager
alx-alexpark
85 × 66 mm69 parts2LNo license1Eps bacural1
RDAsaBranca
90 × 90 mm21 parts2LNo license1STM32
Glider
pdyxs
90 × 80 mm356 parts4LCERN-OHL-S-2.00STM32
Sat mppt
JaronCyna
90.2 × 95.9 mm281 parts6LNo license0DSP-Regulator-RevC
Phil-CIA
100 × 125 mm226 parts2LNo license0STM32
Devhub
mpolci
172.5 × 85 mm212 parts4LMIT0RP2040/RP2350
Onboard Computer
onionsat-pcbs
50 × 50 mm170 parts8LNo license0Sensor kit
cryoskills
130 × 60 mm78 parts2LCERN-OHL-P-2.00Servo-Tester
CodeWorksCZ
135 × 75 mm45 parts2LMIT0Raspberry Pi
NerMo Electronics Stack I
NoMoreBrainToUse
74 × 36 mm42 parts4LNo license0Battery-Featherwing
mousethief
23.4 × 51.3 mm37 parts2LNo license0Pacakge
Lightiam
267 × 111.8 mm27 parts9LNo license0- schematic only · 54 partsRP2040/RP2350
SmartCellAnalyzer
asithniwantha
54 partsMIT0 ORION POWER BOARD
AshishA26
70 × 55 mm15 parts2LNo license253RP2040/RP2350
PID Toaster
benkyd
119.8 × 126 mm105 parts2LNo license1RP2040/RP2350
Gaia obc stencil
onionsat-pcbs
0.6 × 9 mm161 parts2LNo license0STM32
DSP-Regulator-HAT-RevB
Phil-CIA
100 × 102.6 mm158 parts2LNo license0Realop1 powerdis bak1
Space-and-Satellite-Systems-UC-Davis
90 × 90 mm95 parts4LNo license0RP2040/RP2350
Robot
dyu134
70.1 × 100 mm78 parts2LNo license0ESP32
DSP-Regulator-HAT-RevC
Phil-CIA
100 × 102.6 mm158 parts2LNo license0Power eta6003-5v ups
smkent
40 × 40 mm66 parts2LCC-BY-SA-4.00
How designs wire the INA3221
Read from the KiCad layouts of 27 open source designs, one per repository: what each pin of the INA3221 connects to, and the resistors, capacitors and other passives placed on it.
- The SCL pin has a pull-up to 3.3V on 23 of 27 designs, most often 10 kΩ (then 4.7 kΩ).
- The SDA pin has a pull-up to 3.3V on 23 of 27 designs, most often 10 kΩ (then 4.7 kΩ).
- The VS pin has a decoupling capacitor on 20 of 27 designs, most often 100 nF (then 1 µF).
- The VPU pin has a decoupling capacitor on 14 of 27 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IN-3pin 1 | Connected to: Signal 52% · not connected 19% · 3.3V 30% |
|
| IN+3pin 2 | Connected to: Signal 59% · not connected 19% · 3.3V 22% |
|
| GNDpin 3 | Connected to: GND 100% | — |
| VSpin 4 | Connected to: 3.3V 89% |
|
| SCLpin 6 | Connected to: The microcontroller 41%, a connector 37%, INA3221 30% |
|
| SDApin 7 | Connected to: The microcontroller 41%, a connector 37%, INA3221 30% |
|
| WARNINGpin 8 | Connected to: The microcontroller 22% · not connected 44% |
|
| CRITICALpin 9 | Connected to: The microcontroller 26% · not connected 33% |
|
| IN-1pin 11 | Connected to: Signal 63% · 5V 30% |
|
| IN+1pin 12 | Connected to: Signal 59% · 5V 33% |
|
| TCpin 13 | Connected to: Not connected 48% · a signal 48% |
|
| IN-2pin 14 | Connected to: Signal 59% · 5V 37% |
|
| IN+2pin 15 | Connected to: Signal 67% · 5V 26% |
|
| VPUpin 16 | Connected to: 3.3V 70% · a signal 26% |
|
| EPpin 17 | Connected to: GND 78% · not connected 22% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Glider by Modos-Labs, Orion - Control Board by AshishA26, TougherPowerMonitor-HW by ahillbom and Bench psu monitor by fixthepixel.
The INA3221 in open source designs
The gallery holds 35 open source boards using the INA3221 from 30 GitHub repositories; a typical one measures about 90 × 78.1 mm and carries around 78 components.
56% are two-layer designs, the rest use four layers or more, and 49% carry an open source license.
The most starred is Glider by Modos-Labs.
Parts used alongside the INA3221
Microcontrollers on boards using the INA3221
What boards using the INA3221 are built for
INA3221: common questions
Where can I find a INA3221 reference design?
Each of the 35 boards on this page is a real design using the INA3221. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the INA3221 SCL pin?
The SCL pin has a pull-up to 3.3V on 23 of 27 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 27 open source designs using the INA3221.
What pull-up resistor is used on the INA3221 SDA pin?
The SDA pin has a pull-up to 3.3V on 23 of 27 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 27 open source designs using the INA3221.
What decoupling capacitors do designs use on the INA3221 VS pin?
The VS pin has a decoupling capacitor on 20 of 27 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 27 open source designs using the INA3221.
What parts are used alongside the INA3221?
The CN3791, FUSB302BMPX, MT9700, USBLC6-2P6 and ADV7611 appear in the most repositories here.
Which microcontrollers do boards using the INA3221 use?
Most are built on STM32 (9), RP2040/RP2350 (5), ESP32 (4) and AVR/Arduino (1).
How big is a typical board using the INA3221?
The median is 90 × 78.1 mm, and 56% are two-layer designs.
What is the most popular open source board using the INA3221?
By GitHub stars, Glider by Modos-Labs, with 2,676 stars.
Can I simulate one of these boards using the INA3221 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.