Momentum-Based-Launch-System-Stasis-

TheArcher2049·Momentum-Based-Launch-System-Stasis-

Momentum-Based-Launch-System-Stasis- PCB layout, top view — open source STM32 board by TheArcher2049

About the Momentum-Based-Launch-System-Stasis- PCB

Momentum-Based-Launch-System-Stasis- is an open source STM32 PCB design by TheArcher2049, published on GitHub. It is a 2-layer board measuring 60.5 × 213.5 mm, with 72 components from 39 distinct parts.

Its main chip is the STM32L031K6Tx, from the STM32 family. Other key parts include the AMS1117-3.3, CC1101RGPR and AP2112K-3.3. By type, the board carries 21 capacitors, 17 resistors, 6 diodes, 4 ICs, 4 connectors and 4 jumpers.

It belongs with the robotics & motion, rf & radio and sensors designs in this gallery.

From the project

Maan Abdelhamid, Archir Luhana, Godrein Owusu

Maan Abdelhamid, Archir Luhana, Godrein Owusu

Stasis is a two-subsystem embedded hardware project inspired by the Sheikah Slate's Stasis rune from The Legend of Zelda: Breath of the Wild. The system simulates the ability to "freeze" an object, accumulate momentum, and launch it upon release.

The user swings a handheld Stasis Remote to capture swing power and direction. After a 9-second countdown, the data is transmitted wirelessly to a Launchpad, which orients itself to the correct angle and launches a tennis ball at the corresponding power level.

Main components on the Momentum-Based-Launch-System-Stasis-

Momentum-Based-Launch-System-Stasis- bill of materials (BOM)

72 components, 39 distinct parts.

QtyPartRefs
1
AMS1117-3.3
U1
1
STM32L031K6Tx
U2
1
CC1101RGPR
U3
1
AP2112K-3.3
U4
1
AO3406
Q1
1
BSS138
Q2
1
JST PH 3
X1
1
26MHz
Y1
1
Conn_01x02
J1
1
Conn_01x04
J2
1
Conn_01x05
J3
1
Conn_01x06
J4
2
STEMMA_I2C_QT
CONN1, CONN2
2
0.1" Header
JP1, JP2
2
~
JP3, JP4
1
~
LSM6DSOX1
2
SOLDERJUMPER_CLOSED
SJ1, SJ2
1
SOLDERJUMPER
SJ3
1
SW_Push
SW1
1
5mm
LED1
Show 19 more
QtyPartRefs
2
GREEN
D1, D5
1
RED
D2
1
1206 IR 940nm
D3
1
1206 IR 940nm Side
D4
1
1N4148
D6
3
27nH
L1, L3, L4
1
22nH
L2
3
10uF
C1, C5, C6
2
100nF
C2, C3
7
100nF
C4, C8, C9, C10, C11, C12, C13
1
0.1uF
C7
2
27pF
C14, C15
2
3.9pF
C16, C18
2
220pF
C17, C21
1
8.2pF
C19
1
5.6pF
C20
13
10K
R1, R2, R3, R4, R5, R9, R10, R11 +5
3
22
R6, R7, R8
1
56k
R17

Momentum-Based-Launch-System-Stasis- design files

The KiCad project lives in the TheArcher2049/Momentum-Based-Launch-System-Stasis- repository on GitHub; these links point at the commit this page was built from.

Momentum-Based-Launch-System-Stasis-: common questions

What microcontroller does the Momentum-Based-Launch-System-Stasis- use?

The Momentum-Based-Launch-System-Stasis- is built around the STM32L031K6Tx, from the STM32 family.

How big is the Momentum-Based-Launch-System-Stasis- PCB?

The Momentum-Based-Launch-System-Stasis- measures 60.5 × 213.5 mm, has 2 copper layers and is 1.69 mm thick.

How many components are on the Momentum-Based-Launch-System-Stasis-?

72 components, from 39 distinct parts. The full bill of materials is listed on this page.

Where can I download the Momentum-Based-Launch-System-Stasis- design files?

From the TheArcher2049/Momentum-Based-Launch-System-Stasis- repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Momentum-Based-Launch-System-Stasis- design in my own project?

The repository has no license, so all rights stay with TheArcher2049. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Momentum-Based-Launch-System-Stasis- without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards