FilterWheels
wright-group·FilterWheels·controller/circuit board/board.kicad_pcb
About the FilterWheels PCB
FilterWheels is an open source AVR/Arduino PCB design by wright-group, published on GitHub under the CERN-OHL-1.2 license. It is a 2-layer board measuring 336.6 × 95.3 mm, with 61 components from 17 distinct parts.
Its main chip is the ARDUINO_MICRO_SHIELD, from the AVR/Arduino family. By type, the board carries 35 connectors, 24 resistors, 1 IC and 1 capacitor.
From the project
Electronics and harware used to automate the process of moving optical filter wheels during experiments.
Electronics and harware used to automate the process of moving optical filter wheels during experiments.
See documentation.pdf for full information.
The daemons in this repository (./wright-filter-wheels) in outdated and unmaintained; instead, use the wright-stepper-motor-box kind found in yaqd-wright.
Main components on the FilterWheels
FilterWheels bill of materials (BOM)
61 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ARDUINO_MICRO_SHIELD | ARDUINO_MICRO_SHIELD | U1 |
| 1 | DRIVER 0 | driver | P1 |
| 6 | DB9 | Pin_Header_Straight_1x07 | P2, P8, P14, P20, P26, P31 |
| 1 | POWER | WireConnection_2.50mmDrill | P3 |
| 6 | LED H | Socket_Strip_Straight_1x02 | P4, P9, P15, P21, P27, P32 |
| 6 | LED S | Socket_Strip_Straight_1x02 | P5, P11, P17, P23, P28, P33 |
| 6 | LED F | Socket_Strip_Straight_1x02 | P6, P12, P18, P24, P29, P34 |
| 1 | DRIVER 1 | driver | P7 |
| 1 | HC259 | DIP-16_W7.62mm | P10 |
| 1 | DRIVER 2 | driver | P13 |
| 2 | HC4351 | DIP-20_W7.62mm | P16, P22 |
| 1 | DRIVER 3 | driver | P19 |
| 1 | DRIVER 4 | driver | P25 |
| 1 | DRIVER 5 | driver | P30 |
| 1 | FAN | Socket_Strip_Straight_1x02 | P35 |
| 1 | CP1 | C_Radial_D8_L11.5_P3.5 | C1 |
| 24 | R | Resistor_Horizontal_RM15mm | R1, R2, R3, R4, R5, R6, R7, R8 +16 |
FilterWheels design files
The KiCad project lives in the wright-group/FilterWheels repository on GitHub; these links point at the commit this page was built from.
FilterWheels: common questions
What microcontroller does the FilterWheels use?
The FilterWheels is built around the ARDUINO_MICRO_SHIELD, from the AVR/Arduino family.
How big is the FilterWheels PCB?
The FilterWheels measures 336.6 × 95.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the FilterWheels?
61 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the FilterWheels design files?
From the wright-group/FilterWheels repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the FilterWheels design in my own project?
Yes, under the terms of its CERN-OHL-1.2 license, which wright-group chose for the repository.
Can I test firmware for the FilterWheels without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k