STM32F469 / DISEN - Placement review
yakuptrkn42-create·ai_pcb_design·PCB_Placement_Review/Project/STM32F469_DISEN_RevI.kicad_pcb
About the STM32F469 / DISEN - Placement review PCB
STM32F469 / DISEN - Placement review is an open source PCB design by yakuptrkn42-create, published on GitHub. It is a 4-layer board measuring 46 × 40 mm, with 37 components from 30 distinct parts.
Other key parts include the TPS61165DBVR and TLV3011BIDBVR. By type, the board carries 16 resistors, 10 capacitors, 5 connectors, 2 ICs, 2 diodes and 1 fuse.
From the project
Güncel teslim: videodan gözlem kaydı ve ayrı bir bağlantı önerisi; paylaşılan üç blok görseli KiCad sayfaları olarak da oluşturuldu.
Güncel teslim: videodan gözlem kaydı ve ayrı bir bağlantı önerisi; paylaşılan üç blok görseli KiCad sayfaları olarak da oluşturuldu.
- Tüm KiCad projeleri, PDF, parça/GPIO tabloları ve video kanıtları — ZIP - Bağlantı önerisi P1 — 7 sayfalı PDF - Video inceleme raporu ve yakın görüntüler — PDF - Açılış ve kapsam · Zaman/kesinlik tablosu
Öneri projesini AIESVideoSchematicReviewR1/Proposal/Project/AIESOneriP1.kicadpro ile KiCad 9'da açın. P1 ERC: 0 hata / 0 uyarı; 157 pin–net eşlemesi kontrol edildi.** GPIO/adres/LED sırası mühendislik seçimidir; mevcut yüklü firmware uyumu bilinmiyor…

Main components on the STM32F469 / DISEN - Placement review
STM32F469 / DISEN - Placement review bill of materials (BOM)
37 components, 30 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS61165DBVR | SOT-23-6 | U1 |
| 1 | TLV3011BIDBVR | SOT-23-6 | U2 |
| 1 | FH26W-25S-0.3SHW(60) | FH26W-25S-0.3SHW | J1 |
| 1 | FH26W-39S-0.3SHW(60) | FH26W-39S-0.3SHW | J2 |
| 1 | FH19C-6S-0.5SH(10) | FH19C-6S-0.5SH | J3 |
| 1 | EXT 5V / 1=GND 2=+5V | PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | SSW-108-02-G-D CN12 1:1 / 2x08 socket | PinSocket_2x08_P2.54mm_Vertical | J5 |
| 1 | 1206L075/6YR 0.75A hold / 6V | Fuse_1206_3216Metric | F2 |
| 1 | SS16 SS16 / 60V 1A | D_SMA | D1 |
| 1 | SS14 SS14 / reverse block | D_SMA | D3 |
| 1 | SLF7045T-220M1R3-H 22uH / shielded | L_TDK_SLF7045 | L1 |
| 1 | 10uF / 16V | C_0805_2012Metric | C1 |
| 1 | 100nF / 16V | C_0805_2012Metric | C2 |
| 1 | 10uF / 50V | C_1210_3225Metric | C3 |
| 1 | 100nF / 50V | C_0805_2012Metric | C4 |
| 1 | 4.7uF / 10V | C_0805_2012Metric | C5 |
| 3 | 100nF / 10V | C_0805_2012Metric | C6, C8, C13 |
| 1 | 1uF / 10V | C_0805_2012Metric | C7 |
| 1 | 220nF / 16V | C_0805_2012Metric | C9 |
| 2 | 4.7k / DNP | R_0805_2012Metric | R1, R2 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 100R | R_0805_2012Metric | R3, R15 |
| 3 | 0R | R_0805_2012Metric | R4, R5, R16 |
| 1 | 100k | R_0805_2012Metric | R6 |
| 1 | 5.23R / 1% | R_0805_2012Metric | R7 |
| 1 | 0R / isolation | R_0805_2012Metric | R12 |
| 1 | 2.2k | R_0805_2012Metric | R13 |
| 2 | 10k | R_0805_2012Metric | R14, R17 |
| 1 | 33k / discharge | R_0805_2012Metric | R18 |
| 1 | 221k / 0.1% | R_0805_2012Metric | R19 |
| 1 | 10k / 0.1% | R_0805_2012Metric | R20 |
STM32F469 / DISEN - Placement review design files
The KiCad project lives in the yakuptrkn42-create/ai_pcb_design repository on GitHub; these links point at the commit this page was built from.
STM32F469 / DISEN - Placement review: common questions
How big is the STM32F469 / DISEN - Placement review PCB?
The STM32F469 / DISEN - Placement review measures 46 × 40 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the STM32F469 / DISEN - Placement review?
37 components, from 30 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the STM32F469 / DISEN - Placement review design files?
From the yakuptrkn42-create/ai_pcb_design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the STM32F469 / DISEN - Placement review design in my own project?
The repository has no license, so all rights stay with yakuptrkn42-create. Use it as a reference, and ask the author before reusing the design.