Awd splitter
2Mon·awd-splitter·PCB/awdsplitter.kicad_pcb
About the Awd splitter PCB
Awd splitter is an open source PCB design by 2Mon, published on GitHub. It is a 2-layer board measuring 28 × 72 mm, with 14 components from 5 distinct parts.
By type, the board carries 4 connectors, 4 fuses, 4 transformers and 2 modules.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
A compact breakout PCB for wiring AWD 3D printers, rated for 105 °C chambers.
Check out my engineering design process in JOURNAL.md!
AWD 3D Printers typically need 12 separate cable runs from the gantry to the electronics bay: four for motors and eight for fans and thermistors. This board collapses that into two 16 pin cables. At the electronics end, either use another PCB to break the 16 pin cables back out, or crimp on your own connectors.

Awd splitter bill of materials (BOM)
14 components, 5 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | MICROFIT_1x4_THT_V | Molex_Nano-Fit_105309-xx04_1x04_P2.50mm_Vertical | M1, M4 |
| 2 | MICROFIT_2x8_THT_V | Molex_Nano-Fit_105310-xx16_2x08_P2.50mm_Vertical | J1, J8 |
| 2 | MICROFIT_1x4_THT_V | Molex_Nano-Fit_105309-xx04_1x04_P2.50mm_Vertical | J2, J5 |
| 4 | MICROFIT_1x2_THT_V | Molex_Nano-Fit_105309-xx02_1x02_P2.50mm_Vertical | F1, F2, F3, F4 |
| 4 | MICROFIT_1x2_THT_V | Molex_Nano-Fit_105309-xx02_1x02_P2.50mm_Vertical | T1, T2, T3, T4 |
Awd splitter design files
The KiCad project lives in the 2Mon/awd-splitter repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/awdsplitter.kicad_pcb
- SchematicPCB/awdsplitter.kicad_sch
Awd splitter: common questions
How big is the Awd splitter PCB?
The Awd splitter measures 28 × 72 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Awd splitter?
14 components, from 5 distinct parts. The full bill of materials is listed on this page.
Where can I download the Awd splitter design files?
From the 2Mon/awd-splitter repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Awd splitter design in my own project?
The repository has no license, so all rights stay with 2Mon. Use it as a reference, and ask the author before reusing the design.
Similar boards
Breakout 112pin Connector
rusefi
174 × 58 mm39 parts2LGPL-3.01.2kEecv breakout
rusefi
140.8 × 53.7 mm9 parts4LGPL-3.01.2kBreakout 60pin EEC-IV
rusefi
139.7 × 62.2 mm15 parts2LGPL-3.01.2k134pin 7-967288-1
rusefi
139.7 × 73.7 mm38 parts2LGPL-3.01.2k88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2kRj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979