LEDEAF Driver
adamgreig·ledeaf·driver/driver.kicad_pcb
About the LEDEAF Driver PCB
LEDEAF Driver is an open source STM32 PCB design by adamgreig, published on GitHub. It is a 2-layer board measuring 42 × 40 mm, with 36 components from 15 distinct parts.
Its main chip is the STM32F411VxTx, from the STM32 family. Other key parts include the XC6206P332MR, IRM-H6xxT and WS2812B. By type, the board carries 21 capacitors, 6 resistors, 4 ICs, 2 switches, 1 crystal and 1 connector.
From the project
This directory contains the PCB design for the driver board.
This directory contains the PCB design for the driver board.
* Issue going into USB bootloader possibly because BOOT1 (PB2) is floating, maybe add a pull-down resistor.
Combine BOOTLOAD and PATTERN buttons into one (wire BOOT0 up to a GPIO) to reduce BOM count. Investigate cheaper STM32 and oscillator. * Add light sensor to allow automatically scaling brightness.
Main components on the LEDEAF Driver
LEDEAF Driver bill of materials (BOM)
36 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XC6206P332MR | SOT-23 | IC1 |
| 1 | IRM-H6xxT | IRM-H6XXT | IC2 |
| 1 | WS2812B | WS2812B | IC3 |
| 1 | STM32F411VxTx | LQFP-100 | IC4 |
| 1 | 20M | XO-32x25 | Y1 |
| 1 | USB4105 | USB4105 | J1 |
| 1 | USER | SW_MOM_6X6 | SW1 |
| 1 | BOOTLOAD | SW_MOM_6X6 | SW2 |
| 1 | 1N4148W | SOD-123 | D1 |
| 10 | 2µ2 | 0603 | C1, C2, C3, C4, C5, C12, C13, C14 +2 |
| 11 | 100n | 0402 | C6, C7, C8, C9, C10, C11, C15, C16 +3 |
| 2 | 5k1 | 0402 | R1, R2 |
| 2 | 10k | 0402 | R3, R6 |
| 1 | 100 | 0402 | R4 |
| 1 | 0R | 0603 | R5 |
LEDEAF Driver design files
The KiCad project lives in the adamgreig/ledeaf repository on GitHub; these links point at the commit this page was built from.
- Layoutdriver/driver.kicad_pcb
- Schematicdriver/driver.kicad_sch
- BOMdriver/JLCSMT_BOM.xlsx
LEDEAF Driver: common questions
What microcontroller does the LEDEAF Driver use?
The LEDEAF Driver is built around the STM32F411VxTx, from the STM32 family.
How big is the LEDEAF Driver PCB?
The LEDEAF Driver measures 42 × 40 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the LEDEAF Driver?
36 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the LEDEAF Driver design files?
From the adamgreig/ledeaf repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the LEDEAF Driver design in my own project?
The repository has no license, so all rights stay with adamgreig. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the LEDEAF Driver without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in ledeaf
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k