34 open source boards using the WS2812B
Real designs built with the WS2812B, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Nixiepipe hardware
tuna-f1sh
48.2 × 49.3 mm45 parts2LCC-BY-SA-4.019AVR/Arduino
Skull badge
b1uN7
163.5 × 163.5 mm101 parts2LNo license15Dc25 spqr badge
netik
152.7 × 76.7 mm109 parts2LApache-2.011Raspberry Pi
Mmm
martamusikmaschine
66.5 × 70.8 mm29 parts2LNo license10Raspberry Pi
Hackpack v4-hardware
twilio
93.5 × 149.9 mm40 parts2LApache-2.06STM32
Embedded-AGC-DSKY-emulator
Gregox273
91 × 120 mm157 parts2LGPL-3.03Hangul-Clock
09labs
99 × 99 mm87 parts2LNo license3BENOTL
eacandelas
93.3 × 102.6 mm59 parts2LApache-2.03AVR/Arduino
Uedaino
fabkominka
50 × 65 mm30 parts2LNo license2Seglow16
abetusk
101.7 × 132.2 mm40 parts5LCC0-1.01AVR/Arduino
Kicad workshop
spacekookie
50 × 50 mm37 parts2LMIT1STM32
LEDEAF Driver
adamgreig
42 × 40 mm36 parts2LNo license1Copper
Toglefritz
17.8 × 12.7 mm7 parts2LNo license1PartyMachine
UnforeseenOcean
113 × 77.5 mm129 parts2LGPL-3.00ESP32
Mini sumo
rv1g-robotics-club
70 × 66 mm76 parts2LNo license0Jerorack
Architeuthis-Flux
9.3 × 14.9 mm28 parts2LUnlicense1ACNode-Shield
londonhackspace
50 × 50 mm15 parts2LNo license14STM32
Fancy node
candykingdom
47.1 × 30.7 mm66 parts4LNo license5STM32
Feeder Testplatine
Tynogc
40 × 64 mm48 parts2LGPL-3.01Jerorack19L
Architeuthis-Flux
6.7 × 5.8 mm19 parts2LUnlicense1NXP
Grove sensor
samuelclay
50.8 × 50.8 mm43 partsNo license16Jerorack19L20-38
Architeuthis-Flux
6.7 × 5.8 mm19 parts2LUnlicense1Arbolito Tronco
ZhengLinLei
68.2 × 102.6 mm26 parts2LCC-BY-NC-4.00Jerorack19R
Architeuthis-Flux
6.7 × 5.8 mm19 parts2LUnlicense1AVR/Arduino
Splitflap controller board
rossbb
96 × 48 mm33 parts2LApache-2.00AVR/Arduino
Splitflap controller board
orgTestCodacy11KRepos110MB
96 × 48 mm33 parts2LApache-2.00AVR/Arduino
Splitflap controller board
nintando64
96 × 48 mm33 parts2LApache-2.00Bottom 8 WS2812B
machadoleonardo94
27 × 36.2 mm17 parts2LNo license0Arbolito Tronco 2
ZhengLinLei
68.2 × 111.1 mm14 parts2LCC-BY-NC-4.00Top 6 WS2812B
machadoleonardo94
27.3 × 30 mm13 parts2LNo license0Panel rgb digits
bfrigon
43.8 × 39.4 mm16 parts2LCC-BY-SA-4.018Mid 2 WS2812B
machadoleonardo94
27.7 × 14.4 mm5 parts2LNo license0Display - RGB Seven Seg. Digit
bfrigon
22.9 × 39.4 mm16 parts2LCC-BY-SA-4.018Rgb dots
bfrigon
11.4 × 29.2 mm4 parts2LCC-BY-SA-4.018
How designs wire the WS2812B
Read from the KiCad layouts of 25 open source designs, one per repository: what each pin of the WS2812B connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 12 of 23 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 5V 83% · a signal 17% |
|
| GNDpin 3 | Connected to: GND 96% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Nixiepipe hardware by tuna-f1sh, Panel rgb digits by bfrigon, Grove sensor by samuelclay and Skull badge by b1uN7.
The WS2812B in open source designs
The gallery holds 34 open source boards using the WS2812B from 26 GitHub repositories; a typical one measures about 50 × 49.6 mm and carries around 33 components.
94% are two-layer designs, the rest use four layers or more, and 56% carry an open source license.
The most starred is Nixiepipe hardware by tuna-f1sh.
Parts used alongside the WS2812B
Microcontrollers on boards using the WS2812B
What boards using the WS2812B are built for
WS2812B: common questions
Where can I find a WS2812B reference design?
Each of the 34 boards on this page is a real design using the WS2812B. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the WS2812B VDD pin?
The VDD pin has a decoupling capacitor on 12 of 23 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 25 open source designs using the WS2812B.
What parts are used alongside the WS2812B?
The 74HC165, arduino_uno_shield, MIC5842, AP111733 and ATmega328P-A appear in the most repositories here.
Which microcontrollers do boards using the WS2812B use?
Most are built on AVR/Arduino (7), STM32 (4), Raspberry Pi (2) and ESP32 (1).
How big is a typical board using the WS2812B?
The median is 50 × 49.6 mm, and 94% are two-layer designs.
What is the most popular open source board using the WS2812B?
By GitHub stars, Nixiepipe hardware by tuna-f1sh, with 19 stars.
Can I simulate one of these boards using the WS2812B before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.