Schematic start module sumo IR V0 16 v1
About the Schematic start module sumo IR V0 16 v1
Schematic start module sumo IR V0 16 v1 is an open source AVR/Arduino PCB design by Alex-C-EE, published on GitHub. It is a 2-layer board measuring 10.4 × 11.4 mm, with 20 components from 15 distinct parts.
Its main chip is the ATTINY13A, from the AVR/Arduino family. By type, the board carries 5 resistors, 2 capacitors, 1 jumper, 1 LED and 1 diode.
From the project
A repo containing original and custom start stop modules for robo sumo and their firmware. Manufacturing files generated.
Prebuilt_Module - this is the module built with pick and place machines.
Schematic start module sumo IR V0 16 v1 bill of materials (BOM)
20 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 5 | — | PAD_50X50 | GND_PAD0, MISO_PAD0, RESET_PAD0, SCK_PAD0, VCC_PAD0 |
| 1 | — | PAD_75X75 | GND_PAD1 |
| 1 | TSOP77338TS | TSOP77338 | IR1 |
| 1 | — | 1X3 | JP1 |
| 1 | — | 1X01 | KILL_SWITCH0 |
| 1 | mosi | PAD_75X75 | MOSI_PAD0 |
| 1 | ATTINY13A | DFN10 | UC0 |
| 1 | — | 0603_SMALL | LED0 |
| 1 | — | SOD523 | D1 |
| 1 | 100NF 100nF | C0603 | C1 |
| 1 | 1UF 1uf | C0603 | C2 |
| 1 | 100OHM 100Ohm | R0603 | R1 |
| 1 | 470 | R0603 | R2 |
| 1 | 1K | R0603 | R3 |
| 2 | 1KOHM 1KOhm | R0603 | R4, R5 |
Schematic start module sumo IR V0 16 v1 design files
The KiCad project lives in the Alex-C-EE/StartStopModule repository on GitHub; these links point at the commit this page was built from.
Schematic start module sumo IR V0 16 v1: common questions
What microcontroller does the Schematic start module sumo IR V0 16 v1 use?
The Schematic start module sumo IR V0 16 v1 is built around the ATTINY13A, from the AVR/Arduino family.
How big is the Schematic start module sumo IR V0 16 v1?
The Schematic start module sumo IR V0 16 v1 measures 10.4 × 11.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Schematic start module sumo IR V0 16 v1?
20 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Schematic start module sumo IR V0 16 v1 design files?
From the Alex-C-EE/StartStopModule repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Schematic start module sumo IR V0 16 v1 design in my own project?
The repository has no license, so all rights stay with Alex-C-EE. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Schematic start module sumo IR V0 16 v1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in StartStopModule
Similar boards
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoV4
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k
AVR/ArduinoMegadesk
gcormier
41.7 × 32.2 mm23 parts2LGPL-3.0818
AVR/ArduinoEasyduino Atmega Nano
Hanqaqa
43.4 × 18 mm30 parts4LCERN-OHL-P-2.0746