HardLabs

DynamicSystemsAndControl

almondsun·DynamicSystemsAndControl·project/pcb/buck.kicad_pcb

DynamicSystemsAndControl PCB layout, top view — open source STM32 board by almondsun
Simulate this board

About the DynamicSystemsAndControl PCB

DynamicSystemsAndControl is an open source STM32 PCB design by almondsun, published on GitHub. It is a 2-layer board measuring 99 × 99 mm, with 57 components from 41 distinct parts.

Its main chip is the STM32 CABLE 2x5, from the STM32 family. Other key parts include the IR2110PBF DIP14, L7805CV, SN74HCT14N, SN74HCT00N and LM393P. By type, the board carries 17 capacitors, 15 resistors, 9 test points, 6 ICs, 3 connectors and 2 transistors.

It belongs with the power & battery designs in this gallery.

From the project

Dynamic Systems and Control coursework: Buck converter modeling, reports, KiCad PCB and STM32 firmware

Paquete de ingeniería para revisión. Fabricación retenida hasta completar la calificación de componentes y el prototipo soldado. No se ha comprado, fabricado, ensamblado ni probado físicamente esta tarjeta.

El diseño original conserva 12 V, 660 µH, 20 µF, 6 Ω y PWM de 10 kHz del proyecto de Sistemas Dinámicos y Control. Emplea dos inductores de 330 µH en serie, IR2110, MOSFET IRFZ44N, rectificación 1N5822 y una Blue Pill externa. El controlador PI conserva la interfaz existente buckupdate en voltios y la salida invertida d′ = 1 − d**. La protección por corriente y tensión es independiente…

Main components on the DynamicSystemsAndControl

IR2110PBF DIP14L7805CVSN74HCT14NSN74HCT00NLM393PINA180A1IDBVR

DynamicSystemsAndControl bill of materials (BOM)

57 components, 41 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
IR2110PBF DIP14
U1
1
L7805CV
U2
1
SN74HCT14N
U3
1
SN74HCT00N
U4
1
LM393P
U5
1
INA180A1IDBVR
U6
1
IRFZ44N TO-220
Q1
1
2N3904
Q2
1
12V FUSED INPUT
J1
1
LOAD + / -
J2
1
STM32 CABLE 2x5
J3
1
0.050R 1% 1W
RS1
1
VIN
TP1
1
GND
TP2
1
SW
TP3
1
GATE
TP4
1
VOUT
TP5
1
ISENSE
TP6
1
SD
TP7
1
NTRIP
TP8
Show 21 more
QtyPartRefs
1
MCU_PWM
TP9
1
1N5822 40V 3A
D1
1
UF4004
D2
2
330uH >=3A Isat VERIFY
L1, L2
2
100uF 25V
C1, C2
4
100nF 50V
C3, C7, C8, C10
2
10uF 35V low ESR
C4, C5
1
1uF 50V X7R
C6
1
330nF 50V
C9
1
10uF 25V
C11
5
100NF
100nF
C12, C13, C14, C15, C16
1
1NF
1nF
C17
1
10R
R1
6
10K
10k
R2, R3, R5, R6, R12, R13
1
1k
R4
1
4.7K
4.7k
R7
1
15k 1%
R8
2
10k 1%
R9, R11
1
31k 1%
R10
1
3k 1%
R14
1
1k 1%
R15

DynamicSystemsAndControl design files

The KiCad project lives in the almondsun/DynamicSystemsAndControl repository on GitHub; these links point at the commit this page was built from.

DynamicSystemsAndControl: common questions

What microcontroller does the DynamicSystemsAndControl use?

The DynamicSystemsAndControl is built around the STM32 CABLE 2x5, from the STM32 family.

How big is the DynamicSystemsAndControl PCB?

The DynamicSystemsAndControl measures 99 × 99 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the DynamicSystemsAndControl?

57 components, from 41 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the DynamicSystemsAndControl design files?

From the almondsun/DynamicSystemsAndControl repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the DynamicSystemsAndControl design in my own project?

The repository has no license, so all rights stay with almondsun. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the DynamicSystemsAndControl without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards