9 open source boards using the LM393P

Real designs built with the LM393P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

9 boardsClear filters|Most starred

How designs wire the LM393P

Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the LM393P connects to, and the resistors, capacitors and other passives placed on it.

  • The 1OUT_1 pin has a pull-up to 5V on 7 of 8 designs, most often 1 kΩ (then 4.7 kΩ).
  • The - pin has a series resistor on 7 of 8 designs, most often 6.8 kΩ (then 10 kΩ).
  • The V- pin is tied to GND on 8 of 8 designs.
  • The + pins have a resistor to GND on 6 of 8 designs, most often 15 kΩ (then 10 kΩ).
1OUT_1pin 1Connected to: MC6821 38%
  • Pull-up to 5V on 88% · 1 kΩ (3), 4.7 kΩ (2), 2.2 kΩ (1)
  • Series resistor on 63% · 1.5 MΩ (3), 100 Ω (2), 270 kΩ (1)
-pin 2Connected to: A connector 25%
  • Series resistor on 88% · 6.8 kΩ (3), 10 kΩ (2), 1 kΩ (2)
  • Pull-up to 5V on 38% · 56 kΩ (3)
+pin 3, 5Connected to: Signal 69% · VREF 19%
  • Resistor to GND on 75% · 15 kΩ (3), 10 kΩ (1), 1 kΩ (1)
  • Series resistor on 63% · 1.5 MΩ (3), 10 kΩ (3), 10 MΩ (3)
  • Pull-up to 5V on 63% · 56 kΩ (3), 10 kΩ (1), 24 kΩ (1)
V-pin 4Connected to: GND 100%
_pin 6Connected to: MC14529B 38%
  • Series resistor on 63% · 20 kΩ (3), 160 kΩ (3), 68 kΩ (2)
  • Capacitor to GND on 63% · 22 pF (3), 3.3 nF (1), 100 nF (1)
2OUT_7pin 7Connected to: MC6821 38% · not connected 25%
  • Pull-up to 5V on 75% · 1 kΩ (3), 4.7 kΩ (1), 20 kΩ (1)
  • Series resistor on 50% · 10 MΩ (3)
V+pin 8Connected to: 12V 88%
  • Decoupling capacitor on 38% · 100 nF (4)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Dragon32Issue2 by jimbro1000, Dragon32Rev3 by jimbro1000, Photomarker tht by SheinbergLab and SYNCHRO Booster by h07jonas.

The LM393P in open source designs

The gallery holds 9 open source boards using the LM393P from 8 GitHub repositories; a typical one measures about 99 × 93.9 mm and carries around 57 components.

89% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.

The most starred is Dragon32Issue2 by jimbro1000.

Microcontrollers on boards using the LM393P

What boards using the LM393P are built for

LM393P: common questions

Where can I find a LM393P reference design?

Each of the 9 boards on this page is a real design using the LM393P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the LM393P 1OUT_1 pin?

The 1OUT_1 pin has a pull-up to 5V on 7 of 8 designs, most often 1 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 8 open source designs using the LM393P.

What resistor goes on the LM393P - pin?

The - pin has a series resistor on 7 of 8 designs, most often 6.8 kΩ (then 10 kΩ). Counted from the KiCad layouts of 8 open source designs using the LM393P.

How is the LM393P V- pin connected?

The V- pin is tied to GND on 8 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the LM393P.

What parts are used alongside the LM393P?

The 74LS02N, 74LS244N, MC14050BCP, MC14529B and MC6809E appear in the most repositories here.

Which microcontrollers do boards using the LM393P use?

Most are built on STM32 (1).

How big is a typical board using the LM393P?

The median is 99 × 93.9 mm, and 89% are two-layer designs.

What is the most popular open source board using the LM393P?

By GitHub stars, Dragon32Issue2 by jimbro1000, with 8 stars.

Can I simulate one of these boards using the LM393P before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part