Pi eeprom programmer
andrewteall·pi-eeprom-programmer·hardware/design/pi-eeprom-programmer.kicad_pcb
About the Pi eeprom programmer PCB
Pi eeprom programmer is an open source Raspberry Pi PCB design by andrewteall, published on GitHub under the MIT-0 license. It is a 2-layer board measuring 70 × 56 mm, with 4 components from 4 distinct parts.
Its main chip is the Raspberry Pi GPIO Connector, from the Raspberry Pi family. Other key parts include the ZIF Socket and 24C01-24C1024. By type, the board carries 2 ICs and 2 connectors.
It belongs with the usb & debug tools designs in this gallery.
From the project
A Raspberry Pi GPIO EEPROM reader and writer
A way to write Parallel and Serial EEPROMs using the Raspberry Pi GPIO pins.
This README provides an overview of the features, hardware design, and usage instructions for the Raspberry Pi EEPROM Programmer.
- Kicad Project File: The Kicad 6 project file to open the designs. - Schematic: The schematic diagram detailing the connections between components and the Raspberry Pi. - PCB Layout: The PCB layout design files used for creating the physical printed circuit board.
Main components on the Pi eeprom programmer
Pi eeprom programmer bill of materials (BOM)
4 components, 4 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ZIF Socket | DIP-28_W15.24mm_Socket | U1 |
| 1 | 24C01-24C1024 | DIP-8_W7.62mm_Socket | U2 |
| 1 | Raspberry Pi GPIO Connector | PinSocket_2x20_P2.54mm_Horizontal | J1 |
| 1 | CONN_01X03 Conn_01x03 | PinHeader_1x03_P2.54mm_Vertical | J2 |
Pi eeprom programmer design files
The KiCad project lives in the andrewteall/pi-eeprom-programmer repository on GitHub; these links point at the commit this page was built from.
Pi eeprom programmer: common questions
What microcontroller does the Pi eeprom programmer use?
The Pi eeprom programmer is built around the Raspberry Pi GPIO Connector, from the Raspberry Pi family.
How big is the Pi eeprom programmer PCB?
The Pi eeprom programmer measures 70 × 56 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Pi eeprom programmer?
4 components, from 4 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Pi eeprom programmer design files?
From the andrewteall/pi-eeprom-programmer repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Pi eeprom programmer design in my own project?
Yes, under the terms of its MIT-0 license, which andrewteall chose for the repository.
Can I test firmware for the Pi eeprom programmer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507