Hot plate controller

Angelo13C·hot-plate·electronics/controller/hot-plate-controller.kicad_pcb

Hot plate controller PCB layout, top view — open source STM32 board by Angelo13C

About the Hot plate controller PCB

Hot plate controller is an open source STM32 PCB design by Angelo13C, published on GitHub. It is a 4-layer board measuring 52 × 52 mm, with 80 components from 51 distinct parts.

Its main chip is the STM32F730R8T6, from the STM32 family. Other key parts include the USBLC6-2SC6 and AP63203WU-7. By type, the board carries 21 connectors, 21 capacitors, 19 resistors, 6 diodes, 3 ICs and 3 transistors.

From the project

It's based on an STM32F730R8T6. The board receives stable 24V from an external power supply unit and requires around 10A of current.

It's based on an STM32F730R8T6. The board receives stable 24V from an external power supply unit and requires around 10A of current.

On the board there's a switching regulator that converts the 24V to 3.3V, which is used by: thermistors, display, MLX90614 and microcontroller.

Main components on the Hot plate controller

Hot plate controller bill of materials (BOM)

80 components, 51 distinct parts.

QtyPartRefs
1
STM32F730R8T6
U1
1
USBLC6-2SC6
U2
1
AP63203WU-7
U3
2
AON7524
Q1, Q2
1
MCU45P04-TP
Q3
1
8MHz
Y1
1
USB_C_Receptacle_USB2.0
J1
1
Display_Connector
J2
1
Hot_Plate_Connector
J3
1
Fan_Connector
J4
1
MLX90614_Connector
J5
1
Thermistor_1_Connector
J6
1
Thermistor_2_Connector
J7
1
Power_Supply_Connector
J8
1
SWD_Connector
J9
1
Extra_PC8
J10
1
Extra_PC9
J11
1
Extra_PA8
J12
1
Extra_PA9
J13
1
Extra_PA10
J14
Show 31 more
QtyPartRefs
1
Extra_PC10
J15
1
Extra_PC11
J16
1
Extra_PC12
J17
1
Extra_PB8
J18
1
Extra_PB9
J19
1
Extra_PC14
J20
1
Extra_PC15
J21
1
12A
F1
1
500mA
F2
2
SW_Push
SW1, SW2
1
Board_Thermistor
TH1
1
RED
D1
3
GREEN
D2, D3, D4
1
D_Zener
D5
1
SK510A-LTP
D6
1
10μH
L1
8
100nF
C1, C2, C3, C4, C5, C6, C12, C18
2
4.7μF
C7, C8
2
30pF
C9, C10
1
0.1μF
C11
1
47μF
C13
3
10μF
C14, C15, C16
4
3.3μF
C17, C19, C20, C21
2
5.1KΩ
R1, R2
1
2.7KΩ
R3
6
4.7KΩ
R4, R13, R14, R15, R17, R18
3
2.2KΩ
R5, R6, R12
1
47Ω
R7
2
300Ω
R8, R10
3
10KΩ
R9, R11, R16
1
100KΩ
R19

Hot plate controller design files

The KiCad project lives in the Angelo13C/hot-plate repository on GitHub; these links point at the commit this page was built from.

Hot plate controller: common questions

What microcontroller does the Hot plate controller use?

The Hot plate controller is built around the STM32F730R8T6, from the STM32 family.

How big is the Hot plate controller PCB?

The Hot plate controller measures 52 × 52 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Hot plate controller?

80 components, from 51 distinct parts. The full bill of materials is listed on this page.

Where can I download the Hot plate controller design files?

From the Angelo13C/hot-plate repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Hot plate controller design in my own project?

The repository has no license, so all rights stay with Angelo13C. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Hot plate controller without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards