Beal-RX
anobli·beal-hw·Beal-Rx/Beal-RX.kicad_pcb
About the Beal-RX PCB
Beal-RX is an open source STM32 PCB design by anobli, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 112 × 38 mm, with 71 components from 28 distinct parts.
Its main chip is the STM32C031K6U6, from the STM32 family. Other key parts include the LTV-844S, TPSM863253RDXR and LORA-E5 LORAWAN MODULE. By type, the board carries 35 resistors, 22 capacitors, 6 ICs, 4 connectors, 2 diodes and 1 switch.
It belongs with the rf & radio and power & battery designs in this gallery.
From the project
Kicad project for a Lora valves controller
Beal-Rx clips onto an existing irrigation controller's zone-output wiring, senses which zone it's energizing, and reports that over LoRa to one or more Beal-TX units. It is the LoRa coordinator of a Beal system — it's where commands originate, and it's already the natural central device since it's the one wired to the existing controller.
The schematic is split into three sheets: Inputs, Radio, Power.
Main components on the Beal-RX
Beal-RX bill of materials (BOM)
71 components, 28 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | LTV-844S | SMDIP-16_W9.53mm | U1, U3, U4 |
| 1 | TPSM863253RDXR TPSM863253 | Texas_RDX0007A_QFN-FCMOD-7-3.3x4mm-P0.5mm_4EP | U2 |
| 1 | LORA-E5 LORAWAN MODULE LoRa-E5 | LoRa-E5 | U5 |
| 1 | STM32C031K6U6 STM32C031K6Ux | QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U6 |
| 1 | CONMHF1-SMD-T | CONMHF1SMDT | J1 |
| 1 | Conn_02x04_Odd_Even | PinHeader_2x04_P1.00mm_Vertical_SMD | J2 |
| 1 | TBL004-508-14BE-2GY | TBL004-508-14BE-2GY | J4 |
| 1 | UJ20-C-H-G-MSMT-4B-P16-TR | UJ20CHGMSMT4BP16TR | J5 |
| 1 | TS02-66-43-BK-160-LCR-D SW_Push | SW_PUSH_6mm | SW2 |
| 1 | SZESD9B5.0ST5G | D_SOD-923 | D1 |
| 1 | led red 1206 LED | LED_0603_1608Metric | D3 |
| 1 | 0K 0603 0 | L_0603_1608Metric | L2 |
| 1 | 0.1uF 16V 0805 0.1uF | C_0805_2012Metric | C1 |
| 1 | GRM155R71C103KA01D 10nF | C_0402_1005Metric | C3 |
| 13 | 1uF 16V 0603 1uF | C_0603_1608Metric | C5, C8, C22, C23, C24, C25, C26, C34 +5 |
| 1 | C0805C106K8PACTU 10uF | C_0805_2012Metric | C6 |
| 1 | 08053C104KAT2A 0.1uF | C_0805_2012Metric | C7 |
| 2 | 4.7uF 10V 0805 4.7uF | C_0805_2012Metric | C10, C11 |
| 2 | 0.1uF 10V 0805 0.1uF | C_0805_2012Metric | C12, C13 |
| 1 | MSASL219LB5226MTNA01 23uF | C_0805_2012Metric | C27 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 5.1K 0402 5.1k | R_0402_1005Metric | R1, R2 |
| 1 | CRCW040219K1FKED 19.1k | R_0402_1005Metric | R3 |
| 1 | CRCW040210K0FKED 10k | R_0402_1005Metric | R4 |
| 12 | 2.2K 0402 2.2k | R_0402_1005Metric | R5, R7, R8, R28, R33, R34, R37, R38 +4 |
| 1 | 1K 0402 1k | R_0402_1005Metric | R6 |
| 1 | 470 0402 470 | R_0402_1005Metric | R9 |
| 5 | 10K 0402 10k | R_0402_1005Metric | R13, R23, R49, R50, R51 |
| 12 | 47K 0402 47k | R_0402_1005Metric | R29, R30, R31, R32, R35, R36, R43, R44 +4 |
Beal-RX design files
The KiCad project lives in the anobli/beal-hw repository on GitHub; these links point at the commit this page was built from.
- LayoutBeal-Rx/Beal-RX.kicad_pcb
- SchematicBeal-Rx/Beal-RX.kicad_sch
Beal-RX: common questions
What microcontroller does the Beal-RX use?
The Beal-RX is built around the STM32C031K6U6, from the STM32 family.
How big is the Beal-RX PCB?
The Beal-RX measures 112 × 38 mm, has 2 copper layers and is 1.579 mm thick.
How many components are on the Beal-RX?
71 components, from 28 distinct parts. The full bill of materials is listed on this page.
Where can I download the Beal-RX design files?
From the anobli/beal-hw repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Beal-RX design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which anobli chose for the repository.
Can I test firmware for the Beal-RX without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in beal-hw
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k