SD-1000
aotta·SD-1000·PCB/Kicad5V/SD-10005v.kicad_pcb
About the SD-1000 PCB
SD-1000 is an open source PCB design by aotta, published on GitHub. It is a 2-layer board measuring 72 × 93.2 mm, with 6 components from 5 distinct parts.
By type, the board carries 3 connectors, 1 jumper, 1 switch and 1 diode.
It belongs with the retro computing designs in this gallery.
From the project
Sega flash multicart for SC-3000, SG-1000 and Mark III based on Pico Clone
SD-1000 is a multicart DIY yourself based on cheap "purple" Raspberry Pi Pico clone.
WARNING! "purple" Pico has not the same pinout of original Raspberry "green" ones, you MUST use the clone or you may damage your hardware.
Kicad project and gerbers files for the pcb are in the PCB folder, you need only a diode and a push buttons. The jumper for 5V to B3 must left open. Add you pico clone, and flash the firmware SD1000_cart.uf2 in the Pico by connecting it while pressing button on Pico and drop it in the opened windows on PC. After flashed with firmware, and every time you have to change…

SD-1000 bill of materials (BOM)
6 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SC3000-EDGE SC3000-Edge | CartridgeEdge | CON1 |
| 2 | CONN_01X20 Conn_01x20 | PinSocket_1x20_P2.54mm_Vertical | J1, J2 |
| 1 | 5v | SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 1 | Diode | D_DO-35_SOD27_P7.62mm_Horizontal | D1 |
SD-1000 design files
The KiCad project lives in the aotta/SD-1000 repository on GitHub; these links point at the commit this page was built from.
SD-1000: common questions
How big is the SD-1000 PCB?
The SD-1000 measures 72 × 93.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SD-1000?
6 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SD-1000 design files?
From the aotta/SD-1000 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the SD-1000 design in my own project?
The repository has no license, so all rights stay with aotta. Use it as a reference, and ask the author before reusing the design.
Similar boards
Expansion Card Retrofit
FrameworkComputer
24 × 27.3 mm5 parts2LCC-BY-4.01.1kRgb to hdmi
hoglet67
77 × 97 mm67 parts2LGPL-3.01.0kBuffer
hoglet67
53.9 × 23.2 mm13 parts2LGPL-3.01.0kX1
hoglet67
121.9 × 81.3 mm51 parts2LGPL-3.01.0kAmiga External
hoglet67
21.9 × 76.7 mm6 parts2LGPL-3.01.0kVideoslotadapter
hoglet67
152 × 57.6 mm13 parts2LGPL-3.01.0k