MTMatrixRoundedAgain
About the MTMatrixRoundedAgain PCB
MTMatrixRoundedAgain is an open source PCB design by Architeuthis-Flux, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 82.6 × 53.3 mm, with 19 components from 6 distinct parts.
By type, the board carries 8 diodes, 6 capacitors, 3 connectors and 2 resistors.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
a jumperless breadboard
Here's the second board revision. I was showing the last version off to someone and they offhandedly mentioned that it would be cool if the whole thing fit under the breadboard. I knew this was my plan all along, but it forced me to finally design it before the code gets too specific to the original off-the-cuff design and I get stuck with my poor ~~life~~ design choices.
MTMatrixRoundedAgain bill of materials (BOM)
19 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Address_Control_Power | PinHeader_1x18_P2.54mm_Vertical | J1 |
| 1 | Chip_Select_Measurement | PinHeader_1x18_P2.54mm_Vertical | J2 |
| 1 | Breadboard | Breadboard_Top | J3 |
| 8 | LED_Small_ALT | LED_1206_3216Metric_ReverseMount_Hole1.8x2.4mm | D1, D2, D3, D4, D5, D6, D7, D8 |
| 6 | 10uF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2, C3, C4, C5, C6 |
| 2 | 220R | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R2 |
MTMatrixRoundedAgain design files
The KiCad project lives in the Architeuthis-Flux/breadWare repository on GitHub; these links point at the commit this page was built from.
MTMatrixRoundedAgain: common questions
How big is the MTMatrixRoundedAgain PCB?
The MTMatrixRoundedAgain measures 82.6 × 53.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the MTMatrixRoundedAgain?
19 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the MTMatrixRoundedAgain design files?
From the Architeuthis-Flux/breadWare repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the MTMatrixRoundedAgain design in my own project?
Yes, under the terms of its GPL-3.0 license, which Architeuthis-Flux chose for the repository.
More boards in breadWare
Similar boards
88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2k
134pin 7-967288-1
139.7 × 73.7 mm38 parts2LGPL-3.01.2k
Breakout 60pin EEC-IV
139.7 × 62.2 mm15 parts2LGPL-3.01.2k
Breakout 112pin Connector
174 × 58 mm39 parts2LGPL-3.01.2k
Eecv breakout
140.8 × 53.7 mm9 parts4LGPL-3.01.2k
Rj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979