PI-metal detector
ardad2088·PI-metal_detector·hardware/stm32_metaldetector.kicad_pcb
About the PI-metal detector PCB
PI-metal detector is an open source STM32 PCB design by ardad2088, published on GitHub. It is a 2-layer board measuring 105.7 × 82.2 mm, with 49 components from 32 distinct parts.
Its main chip is the STM32_Blue_Pill_DevBoard, from the STM32 family. Other key parts include the TL072CP, MC7805CT-BP and AP1117-33. By type, the board carries 18 resistors, 11 capacitors, 7 diodes, 4 transistors, 4 connectors and 3 ICs.
From the project
Pulse Induction (PI) Metal Detector Board 2-layer mixed-signal PCB for a pulse induction metal detector.
2-layer mixed-signal PCB for a pulse induction metal detector: an STM32 microcontroller, a high-power MOSFET coil driver and an op-amp analog front end.
A pulse induction detector drives its coil with short, strong current pulses and then looks at the signal that decays after each pulse. A metal target changes that decay, and the change is very small, so the receiving circuit has to amplify and condition it carefully before the microcontroller can use it.
Main components on the PI-metal detector
PI-metal detector bill of materials (BOM)
49 components, 32 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TL072CP Texas Instruments | DIP-8_W7.62mm | U1 |
| 1 | MC7805CT-BP Micro Commercial Co | TO-220-3 | U2 |
| 1 | AP1117-33 | SOT-223-3_TabPin2 | U3 |
| 1 | STM32_Blue_Pill_DevBoard | STM32_Blue_Pill_DevBoard | A1 |
| 1 | IRF740 | TO-220-3_Vertical | Q1 |
| 2 | BC847 BC546 | TO-92_Inline | Q2, Q3 |
| 1 | BC546 | TO-92_Inline | Q5 |
| 1 | PINHD_1X2_MALE Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | Screw_Terminal_2_P3.50mm | PhoenixContact_MC_1,5_4-G-3.81_1x04_P3.81mm_Horizontal | J3 |
| 2 | PINHD_1x20_Male | PinHeader_1x20_P2.54mm_Vertical | J4, J5 |
| 1 | BUZZER_5V Buzzer_5V | MagneticBuzzer_ProSignal_ABT-410-RC | BZ1 |
| 2 | 1N4148 ON Semiconductor | Diode_DO-35_P10mm | D1, D2 |
| 5 | LED | LED_D5.0mm | D3, D4, D5, D6, D7 |
| 4 | 100NF_CERAMIC 100nF_Ceramic | C_Disc_D5.0mm_W2.5mm_P2.50mm | C1, C6, C7, C9 |
| 1 | 4700UF_25V 4700uF_25V | CP_Radial_D22.0mm_P10.00mm_SnapIn | C2 |
| 2 | 1UF_50V 1uF_50V | CP_Radial_D5.0mm_P2.00mm | C3, C8 |
| 1 | 10UF_50V 10uF_50V | CP_Radial_D5.0mm_P2.00mm | C4 |
| 2 | 1000UF_25V 1000uF_25V | CP_Radial_D13.0mm_P5.00mm | C5, C11 |
| 1 | 1000uF_25V | CP_Radial_D8.0mm_P3.50mm | C12 |
| 1 | 390OHM 390ohm | R_Axial_DIN0617_L17.0mm_D6.0mm_P30.48mm_Horizontal | R1 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 6.8K 6.8k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2 |
| 1 | 680OHM 680ohm | R_Axial_DIN0411_L9.9mm_D3.6mm_P25.40mm_Horizontal | R3 |
| 1 | 120OHM 120ohm | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4 |
| 1 | 10K 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5 |
| 1 | 82K 82k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R6 |
| 1 | 18K 18k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R7 |
| 1 | 1M | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R8 |
| 1 | 3.9K 3.9k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R9 |
| 1 | 7.5K 7.5k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R10 |
| 3 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R11, R12, R13 |
| 1 | 220OHM 220 ohms | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R14 |
| 4 | 220 ohms | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R15, R16, R17, R18 |
PI-metal detector design files
The KiCad project lives in the ardad2088/PI-metal_detector repository on GitHub; these links point at the commit this page was built from.
PI-metal detector: common questions
What microcontroller does the PI-metal detector use?
The PI-metal detector is built around the STM32_Blue_Pill_DevBoard, from the STM32 family.
How big is the PI-metal detector PCB?
The PI-metal detector measures 105.7 × 82.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PI-metal detector?
49 components, from 32 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the PI-metal detector design files?
From the ardad2088/PI-metal_detector repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the PI-metal detector design in my own project?
The repository has no license, so all rights stay with ardad2088. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the PI-metal detector without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k