Glove v1
About the Glove v1 PCB
Glove v1 is an open source STM32 PCB design by aykevl, published on GitHub. It is a 2-layer board measuring 15 × 20 mm, with 19 components from 14 distinct parts.
Its main chip is the STM32L031G6Ux, from the STM32 family. Other key parts include the LIS3DH. By type, the board carries 7 resistors, 4 capacitors, 2 ICs, 2 transistors, 2 diodes and 1 battery holder.
From the project
Collection of microcontroller projects
This is my personal stash of small electronics projects, usually written using TinyGo.
I won't guarantee anything about it. All I can say is that it did work for me at some point and I like sharing what I made. Many things are written once and then mostly forgotten so I probably won't provide any support for any of the code.
Feel free to use this code however you wish (in other words, you can treat it as public domain). Especially for small parts I won't mind if you just copy it in your project. For larger pieces of code or if you copy a project entirely, I would appreciate attribution…
Main components on the Glove v1
Glove v1 bill of materials (BOM)
19 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LIS3DH | LGA-16_3x3mm_P0.5mm_LayoutBorder3x5y | U1 |
| 1 | STM32L031G6Ux | QFN-28_4x4mm_P0.5mm | U2 |
| 1 | Q_PMOS_GSD | SOT-23 | Q1 |
| 1 | Q_Photo_NPN_EC | LED_0603_1608Metric | Q2 |
| 1 | Battery_Cell | MY-1220-03 | BT1 |
| 1 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | LED_RAGB | FM-3510RGBA-SG | D1 |
| 1 | D | D_SOD-523 | D2 |
| 3 | 10uF | C_0402_1005Metric | C1, C2, C3 |
| 1 | 100nF | C_0402_1005Metric | C4 |
| 2 | 10k | R_0402_1005Metric | R1, R2 |
| 2 | 220 | R_0402_1005Metric | R3, R4 |
| 2 | 49.9 | R_0402_1005Metric | R5, R6 |
| 1 | 1k | R_0402_1005Metric | R7 |
Glove v1 design files
The KiCad project lives in the aykevl/things repository on GitHub; these links point at the commit this page was built from.
- Layoutglove-v1/glove-v1.kicad_pcb
- Schematicglove-v1/glove-v1.kicad_sch
Glove v1: common questions
What microcontroller does the Glove v1 use?
The Glove v1 is built around the STM32L031G6Ux, from the STM32 family.
How big is the Glove v1 PCB?
The Glove v1 measures 15 × 20 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Glove v1?
19 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Glove v1 design files?
From the aykevl/things repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Glove v1 design in my own project?
The repository has no license, so all rights stay with aykevl. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Glove v1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in things
Similar boards
STM32LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7k
STM32AxxSolder
AxxAxx
39 × 82.5 mm122 parts2LGPL-3.01.7k
STM32AIOC
skuep
21 × 31.5 mm47 parts2LMIT1.4k
STM32Ferris
pierrechevalier83
208.8 × 86.8 mm102 parts2LSHL-2.11.3k
STM32176 pin board
rusefi
61.8 × 73.2 mm76 parts2LGPL-3.01.2k
STM32Brain board STM32F407
61.8 × 73.2 mm69 parts2LGPL-3.01.2k