52 open source boards using the LIS3DH
Real designs built with the LIS3DH, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Dml10
jonnor
52 × 26 mm39 parts2LNo license315ESP32
Blinkekatze
TobleMiner
83 × 83 mm106 parts4LNo license34RP2040/RP2350
AWS IoT ExpressLink Demo Badge
aws
59.2 × 93.1 mm68 parts2LMIT-029STM32
Tracker v1
angelnu
56.5 × 66.8 mm36 parts2LMIT22AVR/Arduino
Ttntrackernode
ttnmapper
48 × 75 mm82 parts2LNo license13ESP8266
TyroBot
TyroElectronics
68 × 49.3 mm44 parts2LGPL-3.013RP2040/RP2350
Luluu
fu5ha
64 × 30 mm57 parts4LNo license9STM32
Main
UBC-Thunderbots
100 × 100 mm186 partsNo license3Xilwatch hw
xil-se
37.8 × 50 mm64 parts2LNo license2STM32
Heart
lime7git
47.6 × 45.2 mm56 parts4LNo license2Nordic nRF
Schematics
LyubomirNachev
85 × 90 mm15 parts2LNo license2NXP
Snap badge hardware
synapse-wireless
63.5 × 127 mm138 parts2LNo license1ESP32
Nerf-ATG-Electronics
nico25112005
56 × 38 mm87 parts4LCC-BY-NC-4.01ESP8266
Endev v1.1
sophiayduan
36 × 70 mm59 parts2LMIT1ESP32
ESP32-S3-keyboard
rappepi
435 × 150 mm575 parts4LCC-BY-NC-4.00Microchip SAM
Samd51 gps alarm clock
KrHaaland
80 × 50 mm149 parts2LNo license0Microchip SAM
SapphineMinimalR6
ChrisHayward-dev
55.9 × 61 mm121 parts4LNo license0STM32
RJX-Embedded-Training-Kit
MUDAL
69.7 × 70.9 mm103 parts2LGPL-3.00Nordic nRF
Keychain rev b panel
olerast67
76 × 72 mm98 parts4LApache-2.00STM32
Avionics-Andromeda
StudentOrganisationForAerospaceResearch
50 × 70 mm86 parts4LNo license0RP2040/RP2350
Christmas-Ornament-2024
jacobantoun
81.4 × 91.5 mm79 parts4LNo license0AVR/Arduino
ButaBoard
azerimaker
71.6 × 94.2 mm79 parts2LNo license0RP2040/RP2350
Generic Pan Tilt
mitmedialab
104 × 57 mm72 parts2LCERN-OHL-P-2.00ESP32
Finder puck
lucy-chapar
72 × 72 mm70 parts4LNo license0ESP32
Lora tracker V3
bendelathouwer
116.3 × 114.5 mm66 parts2LNo license0AVR/Arduino
Entrenador
FrizzyElectronics
115 × 61 mm64 parts2LCustom license0ESP32
Esp32-bluetooth erm accel dongle faulty
manhoosbilli1
23.3 × 28.4 mm50 parts4LNo license0ESP32
Daronjli dongle
manhoosbilli1
45.2 × 29.7 mm50 parts4LNo license0ESP32
Esp32-s3-dev
shades66
46.6 × 32.7 mm48 parts2LNo license0ESP32
Esp32-dongle v0-1-ceramic antenna
manhoosbilli1
11 × 50.8 mm47 parts4LNo license0RP2040/RP2350
Archiater
anayvaidya11
77.5 × 71.8 mm35 parts2LNo license0ESP32
SmartPetCollar
8aChristian
69 × 41 mm30 parts2LMIT0Sensexpansion
Las-Vejas
32 × 25.5 mm11 parts2LNo license0Nordic nRF
Fishping
DjukicAleksej
44.2 × 44.2 mm10 parts2LMIT0- schematic only · 11 parts
Tablet sensor board
explora26
11 partsNo license0 - schematic only · 10 partsAVR/Arduino
Netlistquery
mmalecki
10 partsMIT0
How designs wire the LIS3DH
Read from the KiCad layouts of 42 open source designs, one per repository: what each pin of the LIS3DH connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 33 of 41 designs, most often 100 nF (then 10 µF).
- The VDD_IO pin has a decoupling capacitor on 32 of 42 designs, most often 100 nF (then 10 µF).
- The SCL/SPC pin has a pull-up to 3.3V on 26 of 42 designs, most often 4.7 kΩ (then 10 kΩ).
- The SDA/SDI/SDO pin has a pull-up to 3.3V on 25 of 42 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDD_IOpin 1 | Connected to: 3.3V 88% |
|
| NCpin 2, 3 | Connected to: Not connected 94% | — |
| SCL/SPCpin 4 | Connected to: The microcontroller 86%, a connector 31% |
|
| GNDpin 5, 10, 12 | Connected to: GND 94% | — |
| SDA/SDI/SDOpin 6 | Connected to: The microcontroller 83%, a connector 31% |
|
| CSpin 8 | Connected to: The microcontroller 24% · 3.3V 36% |
|
| INT2pin 9 | Connected to: Not connected 64% · a signal 36% | — |
| ADC3pin 13 | Connected to: Not connected 71% | — |
| VDDpin 14 | Connected to: 3.3V 88% |
|
| ADC2pin 15 | Connected to: Not connected 68% | — |
| ADC1pin 16 | Connected to: Not connected 68% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Dml10 by jonnor, CM5 MINIMA by claynicholson, Glove v1 by aykevl and Blinkekatze by TobleMiner.
The LIS3DH in open source designs
The gallery holds 52 open source boards using the LIS3DH from 45 GitHub repositories; a typical one measures about 63.8 × 61 mm and carries around 59 components.
58% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is Dml10 by jonnor.
Parts used alongside the LIS3DH
Microcontrollers on boards using the LIS3DH
What boards using the LIS3DH are built for
LIS3DH: common questions
Where can I find a LIS3DH reference design?
Each of the 52 boards on this page is a real design using the LIS3DH. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the LIS3DH VDD pin?
The VDD pin has a decoupling capacitor on 33 of 41 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 42 open source designs using the LIS3DH.
What decoupling capacitors do designs use on the LIS3DH VDD_IO pin?
The VDD_IO pin has a decoupling capacitor on 32 of 42 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 42 open source designs using the LIS3DH.
What pull-up resistor is used on the LIS3DH SCL/SPC pin?
The SCL/SPC pin has a pull-up to 3.3V on 26 of 42 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 42 open source designs using the LIS3DH.
What parts are used alongside the LIS3DH?
The AMS1117-3.3, AP2112K-3.3, RP2040, USBLC6-2SC6 and ATmega32U4-AU appear in the most repositories here.
Which microcontrollers do boards using the LIS3DH use?
Most are built on ESP32 (14), AVR/Arduino (7), STM32 (6) and RP2040/RP2350 (6).
How big is a typical board using the LIS3DH?
The median is 63.8 × 61 mm, and 58% are two-layer designs.
What is the most popular open source board using the LIS3DH?
By GitHub stars, Dml10 by jonnor, with 315 stars.
Can I simulate one of these boards using the LIS3DH before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.