HardLabs

Extruder ctrl circuits

biodigitalmatter·extruder_ctrl_circuits·24V_plc_integration_shield/24V_plc_integration_shield.kicad_pcb

Extruder ctrl circuits PCB layout, top view — open source AVR/Arduino board by biodigitalmatter

About the Extruder ctrl circuits PCB

Extruder ctrl circuits is an open source AVR/Arduino PCB design by biodigitalmatter, published on GitHub. It is a 4-layer board measuring 68.6 × 58 mm, with 33 components from 26 distinct parts.

Its main chip is the Arduino_1pin, from the AVR/Arduino family. Other key parts include the 4N35 and JTD2024S05. By type, the board carries 12 connectors, 11 resistors, 3 ICs, 3 diodes, 3 capacitors and 1 inductor.

It belongs with the dev boards & breakouts designs in this gallery.

Main components on the Extruder ctrl circuits

4N35JTD2024S05

Extruder ctrl circuits bill of materials (BOM)

33 components, 26 distinct parts.

QtyPartRefs
2
4N35
U2, U3
1
JTD2024S05
U4
1
Conn_01x04_Male
J1
1
USB_A_Stacked
J2
1
Conn_01x06_Male
J3
1
Screw_Terminal_01x02
J4
1
Conn_01x02_Female
J5
1
Power
P1
1
Analog
P2
1
Digital
P3
1
Digital
P4
3
CONN_01X01
P5, P7, P8
1
Green 20 mA 2.2 Vf
D1
1
Red 2 mA 1.7 Vf
D2
1
Yellow 2 mA 1.85 Vf
D3
1
100 µH 0.5 A
L1
1
470 µF 10V
C1
1
22 µF 50V
C2
1
330 μF 50 V
C3
2
2.7k Ω
R1, R5
Show 6 more
QtyPartRefs
2
100k Ω
R2, R8
2
100 Ω
R3, R7
2
4.7 kΩ
R4, R6
1
1.1 kΩ
R9
1
1.8 kΩ
R10
1
1.6 kΩ
R11

Extruder ctrl circuits design files

The KiCad project lives in the biodigitalmatter/extruder_ctrl_circuits repository on GitHub; these links point at the commit this page was built from.

Extruder ctrl circuits: common questions

What microcontroller does the Extruder ctrl circuits use?

The Extruder ctrl circuits is built around the Arduino_1pin, from the AVR/Arduino family.

How big is the Extruder ctrl circuits PCB?

The Extruder ctrl circuits measures 68.6 × 58 mm, has 4 copper layers and is 4.69 mm thick.

How many components are on the Extruder ctrl circuits?

33 components, from 26 distinct parts. The full bill of materials is listed on this page.

Where can I download the Extruder ctrl circuits design files?

From the biodigitalmatter/extruder_ctrl_circuits repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Extruder ctrl circuits design in my own project?

The repository has no license, so all rights stay with biodigitalmatter. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Extruder ctrl circuits without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards