Nanook mb
burgrp·nanook-mb·board/nanook-mb.kicad_pcb
About the Nanook mb PCB
Nanook mb is an open source STM32 PCB design by burgrp, published on GitHub. It is a 2-layer board measuring 175 × 120 mm, with 77 components from 50 distinct parts.
Its main chip is the STM32F030K6Tx, from the STM32 family. Other key parts include the NCP1117-3.3_SOT223, Mean Well PM-15-5, DRV8833, MCP4706A0T-E/CH and G3MB-5V-SSR. By type, the board carries 23 connectors, 18 resistors, 13 capacitors, 8 ICs, 5 diodes and 4 crystals.
It belongs with the sensors and robotics & motion designs in this gallery.
From the project
NANOOK geothermal heat pump main board
Nanook-mb is control board for open source NANOOK ground-water heat pump project. The board is responsible for:
- soft-switching three phases compressor - switching two circulation pumps - controlling Carel Electronic Expansion Valve - reading - safety low and high pressure switches - water temperature sensors on all exchanger ports (eight sensors in total) - water pressure sensors on cold and hot side - water flow sensors on cold and hot side - refrigerant pressure sensors on cold and hot side - providing configuration web user interface via WiFi connection

Main components on the Nanook mb
Nanook mb bill of materials (BOM)
77 components, 50 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | NCP1117-3.3_SOT223 | SOT-223-3_TabPin2 | U1, U2 |
| 1 | Mean Well PM-15-5 | Mean-Well-PM-15-5 | U3 |
| 1 | STM32F030K6Tx | LQFP-32_7x7mm_P0.8mm | U5 |
| 1 | DRV8833 | TSSOP-16_4.4x5mm_Pitch0.65mm-EP | U6 |
| 1 | MCP4706A0T-E/CH | SOT-23-6 | U7 |
| 2 | G3MB-5V-SSR | G3MB-SSR | U8, U9 |
| 1 | NanoPi-Duo | NanoPi-Duo | M1 |
| 1 | SWD | SWD | X1 |
| 1 | I2C Cold Side | Micro-Match-FOB-6 | X2 |
| 1 | I2C Hot Side | Micro-Match-FOB-6 | X3 |
| 1 | I2C Aux | Micro-Match-FOB-6 | X4 |
| 1 | Power Switch | DG142R-2-5.08 | J1 |
| 1 | Mains L1 | Tab-6.3 | J2 |
| 1 | AUX | PinHeader_2x05_P2.54mm_Vertical | J3 |
| 1 | E2V | DG142R-4-5.08 | J4 |
| 1 | LPS | DG142R-2-5.08 | J5 |
| 1 | Pump Cold Side | DG142R-2-5.08 | J6 |
| 1 | Pump Hot Side | DG142R-2-5.08 | J7 |
| 1 | HPS | DG142R-2-5.08 | J8 |
| 1 | Mains L2 | Tab-6.3 | J9 |
Show 30 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Service | PinHeader_1x06_P2.54mm_Vertical | J10 |
| 1 | Mains L3 | Tab-6.3 | J11 |
| 1 | Mains N | Tab-6.3 | J12 |
| 1 | SSR 220 | DG142R-2-5.08 | J13 |
| 1 | SSR 0-5V | DG142R-2-5.08 | J14 |
| 1 | Compressor L1 | Tab-6.3 | J15 |
| 1 | Compressor L2 | Tab-6.3 | J16 |
| 1 | Compressor L3 | Tab-6.3 | J17 |
| 1 | SSR Output L1 | Tab-6.3 | J18 |
| 1 | SSR Output L2 | Tab-6.3 | J19 |
| 1 | SSR Output L3 | Tab-6.3 | J20 |
| 1 | SSR Input L1 | Tab-6.3 | J21 |
| 1 | SSR Input L2 | Tab-6.3 | J22 |
| 1 | SSR Input L3 | Tab-6.3 | J23 |
| 3 | RELAY_2 | RT314_Relay | K1, K2, K3 |
| 1 | SB2P | SB2P | S1 |
| 1 | BC817 | SOT-23 | T1 |
| 4 | SK22 | D_SMB | D1, D2, D3, D5 |
| 1 | LED_RGB | LED_RGB_5050-6 | D4 |
| 2 | 2F | BCE005R5C205FS | C1, C13 |
| 2 | 1m | CP_Elec_8x10 | C2, C3 |
| 6 | 100n | C_0805_2012Metric | C4, C7, C9, C10, C11, C12 |
| 1 | 10u | C_0805_2012Metric | C5 |
| 1 | 10n | C_0805_2012Metric | C6 |
| 1 | 2.2M | C_0805_2012Metric | C8 |
| 9 | 4k7 | R_0805_2012Metric | R1, R2, R6, R7, R10, R12, R13, R14 +1 |
| 3 | 270R | R_0805_2012Metric | R3, R4, R5 |
| 2 | 0R22 | R_0805_2012Metric | R8, R9 |
| 1 | 1K5 | R_0805_2012Metric | R11 |
| 3 | 4R7/2W | R_2512_6332Metric | R16, R17, R18 |
Nanook mb design files
The KiCad project lives in the burgrp/nanook-mb repository on GitHub; these links point at the commit this page was built from.
- Layoutboard/nanook-mb.kicad_pcb
- Schematicboard/nanook-mb.kicad_sch
Nanook mb: common questions
What microcontroller does the Nanook mb use?
The Nanook mb is built around the STM32F030K6Tx, from the STM32 family.
How big is the Nanook mb PCB?
The Nanook mb measures 175 × 120 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Nanook mb?
77 components, from 50 distinct parts. The full bill of materials is listed on this page.
Where can I download the Nanook mb design files?
From the burgrp/nanook-mb repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Nanook mb design in my own project?
The repository has no license, so all rights stay with burgrp. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Nanook mb without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k