17 open source boards using the DRV8833
Real designs built with the DRV8833, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
BoosterBot
Hylian
60 × 100 mm58 parts2LNo license7RP2040/RP2350
Hardware-Team-2025-2026
Nikhil-42
139.7 × 114.3 mm47 parts4LNo license3STM32
Nanook mb
burgrp
175 × 120 mm77 parts2LNo license2Dreamster board
dreamster
62 × 60 mm50 parts2LNo license1ESP32
Robot
jgraulle
100 × 100 mm183 parts2LNo license0AVR/Arduino
Tito
cdrfiuba
65 × 107.5 mm85 partsNo license0ESP32
Micromouse
wuehr1999
80 × 80.2 mm83 parts2LMIT0ESP32
RC vel car
surya-shreevathsa11
46 × 32 mm70 parts4LNo license0NXP
Board 17
WPISmartmouse
70.5 × 42.6 mm45 parts2LNo license0Pmod DC-motor driver
TVavrinec
37.7 × 16.9 mm24 parts2LNo license0RP2040/RP2350
HolidayExpress
joshkephart
50 × 50 mm17 parts2LNo license0ESP32
Kicadsbot
asimai60
50 × 35 mm12 parts2LNo license0- schematic only · 25 partsESP32
MyoCell
KenKadilar
25 partsMIT0 ESP32
MATRIZ COCHE COMPETENCIA
OttoDotto
62 × 95 mm186 parts2LNo license3ESP32
Eel head pcbs assembly v03
bombarie
53.1 × 24.4 mm19 parts2LCC-BY-NC-4.01AVR/Arduino
COCHE COMPETENCIA
OttoDotto
75 × 65 mm13 parts2LNo license3ESP32
QCM Halo — Pocket QCM-D Instrument
jayis1
90 × 60 mm27 parts4LNo license0
How designs wire the DRV8833
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the DRV8833 connects to, and the resistors, capacitors and other passives placed on it.
- The IN3 pin has a capacitor to the supply on 6 of 13 designs, most often 10 nF (then 100 nF).
- The VINT pin has a capacitor to GND on 6 of 9 designs, most often 2.2 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SLEEPpin 1 | Connected to: The microcontroller 33% · GND 17% |
|
| IN3pin 11 | Connected to: A connector 23% · GND 15% |
|
| VINTpin 14 | Connected to: Signal 100% |
|
12 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BoosterBot by Hylian, Hardware-Team-2025-2026 by Nikhil-42, COCHE COMPETENCIA by OttoDotto and Nanook mb by burgrp.
The DRV8833 in open source designs
The gallery holds 17 open source boards using the DRV8833 from 16 GitHub repositories; a typical one measures about 63.5 × 62.5 mm and carries around 47 components.
80% are two-layer designs, the rest use four layers or more, and 12% carry an open source license.
The most starred is BoosterBot by Hylian.
Parts used alongside the DRV8833
Microcontrollers on boards using the DRV8833
What boards using the DRV8833 are built for
DRV8833: common questions
Where can I find a DRV8833 reference design?
Each of the 17 boards on this page is a real design using the DRV8833. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the DRV8833 IN3 pin connected?
The IN3 pin has a capacitor to the supply on 6 of 13 designs, most often 10 nF (then 100 nF). Counted from the KiCad layouts of 13 open source designs using the DRV8833.
How is the DRV8833 VINT pin connected?
The VINT pin has a capacitor to GND on 6 of 9 designs, most often 2.2 µF (then 100 nF). Counted from the KiCad layouts of 13 open source designs using the DRV8833.
Which microcontrollers do boards using the DRV8833 use?
Most are built on ESP32 (8), AVR/Arduino (2), RP2040/RP2350 (2) and NXP (1).
How big is a typical board using the DRV8833?
The median is 63.5 × 62.5 mm, and 80% are two-layer designs.
What is the most popular open source board using the DRV8833?
By GitHub stars, BoosterBot by Hylian, with 7 stars.
Can I simulate one of these boards using the DRV8833 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.