Pusheenz40
ChrisChrisLoLo·pusheenz40·pcb/sadcatz40/sadcatz40.kicad_pcb
About the Pusheenz40 PCB
Pusheenz40 is an open source STM32 PCB design by ChrisChrisLoLo, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 115.4 × 48.1 mm, with 107 components from 15 distinct parts.
Its main chip is the STM32F072C8TX, from the STM32 family. Other key parts include the USBLC6-2SC6 and XC6206PXXXMR-REGULATOR_LINEAR. By type, the board carries 42 switches, 40 diodes, 9 capacitors, 3 ICs, 3 resistors and 1 connector.
It belongs with the keyboards designs in this gallery.
From the project
A pocket keyboard that uses SMD mouse switches. Low profile and easy to assemble
Disclaimer is that this design has very low tolerances for its key switches. You will likely need a 3D printer such as a Bambu Lab A1/A1 mini/P1P/P1S and set the slicing layer resolution to 0.08mm. Printers like the Prusa i3/mini may also work, but have not been tested.
If you want to assemble/order your own PCBAs, come chat in the discord here! https://discord.gg/m8vwnqJEsc

Main components on the Pusheenz40
Pusheenz40 bill of materials (BOM)
107 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USBLC6-2SC6 | SOT-23-6 | U1 |
| 1 | STM32F072C8TX STM32F072C8Tx | LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | XC6206PXXXMR-REGULATOR_LINEAR XC6206PxxxMR-Regulator_Linear | SOT-23 | U3 |
| 1 | USB2_C_RECEPTACLE USB2_C_Receptacle | Mid_Mount-USB_C | J1 |
| 1 | 500MA 500mA | Fuse_1206_3216Metric | F1 |
| 8 | MountingHole_Pad | m1.6_hole | H1, H2, H3, H4, H5, H6, H7, H8 |
| 40 | SW_Push | SW_SPST_EVQP0 | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +32 |
| 1 | BOOT | SW_SPST_SKQG_WithoutStem | SW41 |
| 1 | RST | SW_SPST_SKQG_WithoutStem | SW42 |
| 40 | D_Small | D_SOD-523 | D1, D2, D3, D4, D5, D6, D7, D8 +32 |
| 5 | 100NF 100nF | C_0402_1005Metric | C1, C4, C5, C6, C7 |
| 1 | 4.7UF 4.7uF | C_0402_1005Metric | C2 |
| 3 | 1UF 1uF | C_0402_1005Metric | C3, C9, C10 |
| 1 | 10K 10k | R_0402_1005Metric | R1 |
| 2 | 5.1K 5.1k | R_0402_1005Metric | R2, R3 |
Pusheenz40 design files
The KiCad project lives in the ChrisChrisLoLo/pusheenz40 repository on GitHub; these links point at the commit this page was built from.
Pusheenz40: common questions
What microcontroller does the Pusheenz40 use?
The Pusheenz40 is built around the STM32F072C8TX, from the STM32 family.
How big is the Pusheenz40 PCB?
The Pusheenz40 measures 115.4 × 48.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Pusheenz40?
107 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Pusheenz40 design files?
From the ChrisChrisLoLo/pusheenz40 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Pusheenz40 design in my own project?
Yes, under the terms of its GPL-3.0 license, which ChrisChrisLoLo chose for the repository.
Can I test firmware for the Pusheenz40 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k