Junebug

CMUAbstract·junebug·kicad/junebug.kicad_pcb

Junebug PCB layout, top view — open source STM32 board by CMUAbstract

About the Junebug PCB

Junebug is an open source STM32 PCB design by CMUAbstract, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 50.8 × 22.9 mm, with 30 components from 18 distinct parts.

Its main chip is the STM32L496RGT3, from the STM32 family. Other key parts include the IS25LP128F-JBLA3, TPS7A0533PDBVR and MMBD4148TW-7-F. By type, the board carries 14 capacitors, 4 ICs, 3 connectors, 3 resistors, 2 crystals and 2 switches.

It belongs with the dev boards & breakouts designs in this gallery.

From the project

Chipsat development board for low-power, embedded computing in space

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.

Main components on the Junebug

Junebug bill of materials (BOM)

30 components, 18 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32L496RGT3
IC1
1
IS25LP128F-JBLA3
IC2
1
TPS7A0533PDBVR
IC3
1
MMBD4148TW-7-F
IC4
1
ABM8AIG-16.000MHZ-12-2Z-T
Y1
1
ABS07AIG-32.768kHz-T
Y2
1
629105150521
J1
2
Conn_01x16
J2, J3
2
PTS810SJM250SMTRLFS
S1, S2
1
599-0010-007F
LEDR1
1
599-0040-007F
LEDY1
3
CC1206JKX7R9BB105
C1, C2, C3
1
CC1206KKX7R7BB475
C4
1
597D158X9004R2T
C5
5
CC0603JPX7R9BB104
C6, C7, C8, C9, C10
4
CC1206CRNPO9BN4R7
C11, C12, C13, C14
2
RT0603FRD07100RL
R1, R2
1
RT0603FRD0710KL
R3

Junebug design files

The KiCad project lives in the CMUAbstract/junebug repository on GitHub; these links point at the commit this page was built from.

Junebug: common questions

What microcontroller does the Junebug use?

The Junebug is built around the STM32L496RGT3, from the STM32 family.

How big is the Junebug PCB?

The Junebug measures 50.8 × 22.9 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Junebug?

30 components, from 18 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Junebug design files?

From the CMUAbstract/junebug repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Junebug design in my own project?

Yes, under the terms of its Apache-2.0 license, which CMUAbstract chose for the repository.

Can I test firmware for the Junebug without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards