Front panel board
cvra·front-panel-board
About the Front panel board
Front panel board is an open source PCB design by cvra, published on GitHub under the Custom license license. It is a 2-layer board measuring 75 × 24 mm, with 29 components from 20 distinct parts.
By type, the board carries 11 connectors, 9 resistors, 7 diodes and 2 switches.
It belongs with the robotics & motion designs in this gallery.
From the project
A simple board to expose the debug connectors of our robots.
This small PCB is used to expose debug and HMI signals from inside the robot to the external world through a front panel. The main goal is to simplify the wiring and have a sturdy mount.
USB Forwarding: Picoblade -> USB Ethernet forwarding: Picoblade -> RJ45 CVRA debug forwarding CAN forwardig 6 LEDS + Team selection indication (RGB) 2 buttons for team selection Connector for the hall sensor starter: 5V, Signal, GND One connector to the nucleo shield for all GPIOs Max width: 80 mm, but lower is better Max length: 30mm Connectors must be at least 1.5mm off the board to go through the panel…

Front panel board bill of materials (BOM)
29 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Conn_01x05 | Molex_PicoBlade_53261-0571_1x05-1MP_P1.25mm_Horizontal | J1 |
| 1 | 10118193-0001LF | _Micro-USB-AB-receptacle-SMT-th-no-slot | J2 |
| 1 | 0532610771 | Molex_PicoBlade_53261-0771_1x07-1MP_P1.25mm_Horizontal | J3 |
| 1 | 0878330821 | 0878330821_02x03_pin_header | J4 |
| 2 | 0532610471 | Molex_PicoBlade_53261-0471_1x04-1MP_P1.25mm_Horizontal | J5, J11 |
| 1 | 0530480410 | Molex-PicoBlade-4-Edge | J6 |
| 1 | Conn_01x03 | Molex_PicoBlade_53261-0371_1x03-1MP_P1.25mm_Horizontal | J7 |
| 1 | 0532611471 | Molex_PicoBlade_53261-1471_1x14-1MP_P1.25mm_Horizontal | J8 |
| 1 | 0532617008 | Molex_PicoBlade_53261-0871_1x08-1MP_P1.25mm_Horizontal | J9 |
| 1 | 615108150221R | 615108150221R_Ethernet_MiddleMount | J10 |
| 2 | CFPA-1FB4-A2T | CFPA-1FB4-A2T | SW1, SW2 |
| 1 | LED_GREEN | LED_0603_RightAngle | D1 |
| 1 | LED_BLUE | LED_0603_RightAngle | D2 |
| 1 | LED_RED | LED_0603_RightAngle | D3 |
| 3 | LED_ORANGE | LED_0603_RightAngle | D4, D5, D6 |
| 1 | CRGB1318FSE | CRGB1318FSE-TM | D7 |
| 2 | 56R | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R2 |
| 4 | 300R | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3, R4, R5, R6 |
| 1 | 130R | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R7 |
| 2 | 30R | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R8, R9 |
Front panel board design files
The KiCad project lives in the cvra/front-panel-board repository on GitHub; these links point at the commit this page was built from.
Front panel board: common questions
How big is the Front panel board?
The Front panel board measures 75 × 24 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Front panel board?
29 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the Front panel board design files?
From the cvra/front-panel-board repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Front panel board design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
Similar boards
Stack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kCube batteryboard
willem-pennings
95 × 95 mm4 parts2LGPL-3.01.1kTrollerv2
rene-dev
100 × 75 mm33 parts4LGPL-3.0979Powerstep
rene-dev
95.2 × 71.5 mm28 parts4LGPL-3.097911ua
rene-dev
57.3 × 19 mm26 parts2LGPL-3.0979Diff driver
rene-dev
32 × 22 mm14 parts2LGPL-3.0979