RecurBOY
cyberboy666·recurBOY·hardware/recurBOY.kicad_pcb
About the RecurBOY PCB
RecurBOY is an open source Raspberry Pi PCB design by cyberboy666, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 100 × 100 mm, with 33 components from 13 distinct parts.
Its main chip is the A-195, from the Raspberry Pi family. Other key parts include the A-2470. By type, the board carries 10 connectors, 8 diodes, 5 switches, 4 resistors, 1 IC and 1 capacitor.
It belongs with the test & measurement and audio designs in this gallery.
From the project
a rpi0 video-instrument – created in collaboration with Guergana Tzatchkova
- this circuit is distributed by UNDERSCORES - an open video hardware label : it is available to purchase - as a pcb, kit or assembled unit - at underscores.shop - the schematic for the circuit can be found here - the pcb gerber files for the lastest version can be found here - interactive BOM is here - link to latest rpi image is here - link to FAQ/TROUBLESHOOTING page can be found here - consider donating to the underscores project to help us continue creating for the commons

Main components on the RecurBOY
RecurBOY bill of materials (BOM)
33 components, 13 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | A-2470 mcp3008 tayda | DIP+SOIC-16 | U1 |
| 4 | A-2563 mono_jack_3.5mm tayda | Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J1, J2, J3, J4 |
| 1 | display_1.8 other | tht_1.8_inch_tft_display | J5 |
| 1 | A-196 Pin_Socket tayda | PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | 490-RCJ-024 rca mouser | tht_vertical_rca | J7 |
| 1 | A-195 2x20_Socket tayda | PinHeader_2x20_P2.54mm_Vertical | J8 |
| 1 | push_5way other | tht_sw_5way | J9 |
| 1 | A-2956 europower tayda | IDC-Header_2x08_P2.54mm_Vertical | J10 |
| 4 | A-5531 10k_pot tayda | Potentiometer_Alps_RK09K_Single_Vertical | RV1, RV2, RV3, RV4 |
| 5 | A-4812 push tayda | SW_PUSH-12mm | SW1, SW2, SW3, SW4, SW5 |
| 8 | A-1095 bat46 tayda | D_DO-35_SOD27_P5.08mm_Vertical_KathodeUp | D1, D2, D3, D4, D5, D6, D7, D8 |
| 1 | A-4008 0.1u tayda | C_Disc_D7.0mm_W2.5mm_P5.00mm | C1 |
| 4 | A-2200 1K tayda | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4 |
RecurBOY design files
The KiCad project lives in the cyberboy666/recurBOY repository on GitHub; these links point at the commit this page was built from.
RecurBOY: common questions
What microcontroller does the RecurBOY use?
The RecurBOY is built around the A-195, from the Raspberry Pi family.
How big is the RecurBOY PCB?
The RecurBOY measures 100 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the RecurBOY?
33 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the RecurBOY design files?
From the cyberboy666/recurBOY repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the RecurBOY design in my own project?
Yes, under the terms of its GPL-3.0 license, which cyberboy666 chose for the repository.
Can I test firmware for the RecurBOY without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507