Flight controller-
Dhruv2212-star·Flight-controller-·PCB/Flight controler.kicad_pcb
About the Flight controller- PCB
Flight controller- is an open source STM32 PCB design by Dhruv2212-star, published on GitHub. It is a 2-layer board measuring 50.5 × 50.5 mm, with 46 components from 36 distinct parts.
Its main chip is the STM32F411CEU6, from the STM32 family. Other key parts include the ICM-42688-P, AP2112K-3.3 and MP2359DJ. By type, the board carries 14 resistors, 13 capacitors, 5 connectors, 4 ICs, 4 diodes and 1 transistor.
It belongs with the sensors, robotics & motion and power & battery designs in this gallery.
From the project
The simplest flight controller that you need! based on STM32 paired with gyro
Measurements: 3-axis Accelerometer, 3-axis Gyroscope. Communication: SPI Interface. The IMU continuously measures angular velocity and acceleration Power-Up Sequence When battery power is applied, the following sequence occurs: Step 1: Battery voltage enters through the XT30 connector. Step 2: The resettable fuse protects the board from excessive current. Step 3: The MP2359DJ converts battery voltage into a regulated +5V supply. Step 4: The AP2112K converts +5V into +3.3V. Step 5: The STM32F411CEU6 receives stable power. Step 6: The crystal oscillator starts generating the system clock. Step…
Main components on the Flight controller-
Flight controller- bill of materials (BOM)
46 components, 36 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ICM-42688-P | PQFN50P300X250X97-14N | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | MP2359DJ | TSOT-23-6 | U3 |
| 1 | STM32F411CEU6 STM32F411CEUx | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U4 |
| 1 | MMBT2222A | TSOT-23-6 | Q1 |
| 1 | Crystal | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | USB | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | 2X3 | PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | 01x04 | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | ESC connector | PinHeader_1x08_P2.54mm_Vertical | J4 |
| 1 | 1X2 | PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Polyfuse | Fuse_1812_4532Metric | F1 |
| 1 | TL3342 SW_Push | SW_SPST_TL3342 | SW1 |
| 1 | POWER | LED_0603_1608Metric | D1 |
| 1 | STATUS | LED_0603_1608Metric | D2 |
| 1 | SS14 D_Schottky | D_SMA | D3 |
| 1 | SMBJ26CA | D_SMB | D4 |
| 1 | 4.7uH | L_6.3x6.3_H3 | L1 |
| 1 | 2.2uf | C_0603_1608Metric | C1 |
Show 16 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 6 | 100nF | C_0603_1608Metric | C2, C3, C4, C7, C10, C11 |
| 2 | 18pf | C_0603_1608Metric | C5, C6 |
| 1 | 22µF, 35V | C_1206_3216Metric | C8 |
| 1 | 22µF, 10V | C_1206_3216Metric | C9 |
| 2 | 1uf | C_0603_1608Metric | C13, C14 |
| 2 | 22 | R_0603_1608Metric | R1, R2 |
| 2 | 5.1K | R_0603_1608Metric | R3, R4 |
| 1 | 1M | R_0603_1608Metric | R5 |
| 1 | 10K | R_0603_1608Metric | R6 |
| 1 | 100K | R_0603_1608Metric | R7 |
| 2 | 1k | R_0603_1608Metric | R8, R10 |
| 1 | 330 | R_0603_1608Metric | R9 |
| 1 | 49.9kΩ | R_0603_1608Metric | R11 |
| 1 | 9.53k | R_0603_1608Metric | R12 |
| 1 | 180kΩ | R_0603_1608Metric | R13 |
| 1 | 27kΩ | R_0603_1608Metric | R14 |
Flight controller- design files
The KiCad project lives in the Dhruv2212-star/Flight-controller- repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/Flight controler.kicad_pcb
- SchematicPCB/Flight controler.kicad_sch
- BOMBOM.csv
Flight controller-: common questions
What microcontroller does the Flight controller- use?
The Flight controller- is built around the STM32F411CEU6, from the STM32 family.
How big is the Flight controller- PCB?
The Flight controller- measures 50.5 × 50.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Flight controller-?
46 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Flight controller- design files?
From the Dhruv2212-star/Flight-controller- repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Flight controller- design in my own project?
The repository has no license, so all rights stay with Dhruv2212-star. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Flight controller- without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k