Chirpkey-8
draarivpatel-ui·chirpkey-8
About the Chirpkey-8 PCB
Chirpkey-8 is an open source AVR/Arduino PCB design by draarivpatel-ui, published on GitHub. It is a 2-layer board measuring 32 × 24 mm, with 10 components from 10 distinct parts.
Its main chip is the ATtiny412-SSNR, from the AVR/Arduino family. By type, the board carries 4 resistors, 1 IC, 1 connector, 1 buzzer, 1 switch and 1 diode.
It belongs with the usb & debug tools designs in this gallery.
From the project
ChirpKey-8: ATtiny412-SSNR 8-pin acoustic FSK & capacitive touch 2-layer KiCad 8 hardware token
ChirpKey-8 is a compact 32 × 24 mm two-layer custom PCB and 36 × 28 × 7.6 mm snap-fit pocket enclosure built around the 8-pin Microchip ATtiny412-SSNR (SOIC-8). It combines a PCB-etched capacitive touch pad (PA6), a tactile mode switch (PA3), differential push-pull piezo acoustic chirp drive (PA1 / PA2), status LED feedback (PA7), and single-wire UPDI programming (PA0) on a single 3.3V coin-cell or header-powered board.

Main components on the Chirpkey-8
Chirpkey-8 bill of materials (BOM)
10 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATtiny412-SSNR Microchip Technology | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | M20-9990345 3V3 / GND / UPDI Harwin | PinHeader_1x03_P2.54mm | J1 |
| 1 | CMT-1203-SMT-TR CMT-1203-SMT-TR (piezo) Same Sky (formerly CUI Devices) | CMT-1203-SMT-TR | BZ1 |
| 1 | B3U-1000P Transmit button Omron | SW_SPST_B3U-1000P | SW1 |
| 1 | LTST-C171KRKT Red LED Lite-On | LED_0805 | D1 |
| 1 | C0805C104K5RACTU 100 nF / 50 V KEMET | C_0805 | C1 |
| 1 | RC0805FR-0710KL 10 kOhm / LED Yageo | R_0805 | R1 |
| 1 | RC0805FR-0710KL 10 kOhm / touch Yageo | R_0805 | R2 |
| 1 | RC0805FR-07220RL 220 Ohm / piezo A Yageo | R_0805 | R3 |
| 1 | RC0805FR-07220RL 220 Ohm / piezo B Yageo | R_0805 | R4 |
Chirpkey-8 design files
The KiCad project lives in the draarivpatel-ui/chirpkey-8 repository on GitHub; these links point at the commit this page was built from.
- Layoutchirpkey8.kicad_pcb
- Schematicchirpkey8.kicad_sch
- BOMbom.csv
Chirpkey-8: common questions
What microcontroller does the Chirpkey-8 use?
The Chirpkey-8 is built around the ATtiny412-SSNR, from the AVR/Arduino family.
How big is the Chirpkey-8 PCB?
The Chirpkey-8 measures 32 × 24 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Chirpkey-8?
10 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Chirpkey-8 design files?
From the draarivpatel-ui/chirpkey-8 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Chirpkey-8 design in my own project?
The repository has no license, so all rights stay with draarivpatel-ui. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Chirpkey-8 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k