Needforheat p1-base hardware
energiegedrag-nl·needforheat-p1-base-hardware·pcb/needforheat-p1-base-hardware.kicad_pcb
About the Needforheat p1-base hardware PCB
Needforheat p1-base hardware is an open source PCB design by energiegedrag-nl, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 51 × 36 mm, with 22 components from 15 distinct parts.
Other key parts include the 74HC14D,653 and EL357N-G. By type, the board carries 7 resistors, 5 diodes, 3 transistors, 3 connectors, 2 ICs and 1 switch.
From the project
Open hardware design files for the NeedForHeat P1-BASE extension module that allows an M5Stack CoreInk to read data from DSMR-compliant smart meters via the P1 port (Voortzetting van energietransitie/needforheat-p1-base-hardware.)
This repository contains the open hardware design files for the NeedForHeat P1-BASE device, which can be used as a CoreInk BASE extension module, on the back of an M5Stack CoreInk device.
The NeedForHeat P1-BASE enables reading smart meters that adhere to the Dutch Smart Meter Requirements via the P1 port.
For the associated firmware that you can run on this device, please see this repository.

Main components on the Needforheat p1-base hardware
Needforheat p1-base hardware bill of materials (BOM)
22 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 74HC14D,653 | SOIC127P600X175-14N | IC1 |
| 1 | EL357N-G | SOP-4_3.8x4.1mm_P2.54mm | U1 |
| 1 | MMBT3904 | SOT-23 | Q1 |
| 1 | MMBT5401 | SOT-23 | Q2 |
| 1 | TBC847_E_20160525 | SOT-23-3 | Q3 |
| 1 | CONN_02X08_COUNTER_CLOCKWISE Conn_02x08_Counter_Clockwise | PinHeader_2x08_P2.54mm_Vertical | J1 |
| 2 | RJ12 | RJ25_Wayconn_MJEA-660X1_Horizontal | J2, J3 |
| 1 | KF1001-03P-R0-GL-DFT-01B | DIP-6_W7.62mm_Socket | SW1 |
| 5 | 1N5819WS | D_SOD-323 | D1, D2, D3, D4, D5 |
| 1 | C49678 C_Small | C_0805_2012Metric | C1 |
| 2 | 2K2 2k2 | R_0805_2012Metric | R1, R4 |
| 2 | 1k | R_0805_2012Metric | R2, R3 |
| 1 | 680 | R_0805_2012Metric | R5 |
| 1 | 10K 10k | R_0805_2012Metric | R6 |
| 1 | 0 | R_0805_2012Metric | R7 |
Needforheat p1-base hardware design files
The KiCad project lives in the energiegedrag-nl/needforheat-p1-base-hardware repository on GitHub; these links point at the commit this page was built from.
Needforheat p1-base hardware: common questions
How big is the Needforheat p1-base hardware PCB?
The Needforheat p1-base hardware measures 51 × 36 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Needforheat p1-base hardware?
22 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Needforheat p1-base hardware design files?
From the energiegedrag-nl/needforheat-p1-base-hardware repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Needforheat p1-base hardware design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which energiegedrag-nl chose for the repository.