11 open source boards using the EL357N-G
Real designs built with the EL357N-G, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Plant Partner PCB 1.0
aboler
148.3 × 69 mm82 parts2LNo license3ESP32
Smart air
meeTeam05
100 × 100 mm62 parts2LMIT1ESP32
RoomThermostat
henkjannl
90 × 54 mm62 parts2LMIT1IoT-Environmental-Monitoring-System
Chethien1912
99.4 × 99.3 mm67 parts2LMIT0ESP32
Blockchain iot
meeTeam05
100 × 100 mm62 parts2LMIT0Needforheat p1-base hardware
energietransitie
51 × 36 mm22 parts2LCERN-OHL-P-2.00Needforheat p1-base hardware
energiegedrag-nl
51 × 36 mm22 parts2LCERN-OHL-P-2.00ESP32
Test 09. With ESP module
henkjannl
90 × 54 mm62 parts2LMIT1ESP32
Test 08. With ESP32 mini
henkjannl
72 × 32 mm25 parts2LMIT1Test 07. Component assignment
henkjannl
40 × 36 mm21 parts2LMIT1ESP32
Interconnect
henkjannl
96 × 75 mm12 parts2LMIT1
How designs wire the EL357N-G
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the EL357N-G connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 7 of 7 designs, most often 10 kΩ (then 680 Ω).
- Pin 2 is tied to GND on 6 of 7 designs.
- Pin 3 has a series resistor on 3 of 7 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 2 | Connected to: GND 86% | — |
| Pin 3 | Connected to: A connector 29% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Plant Partner PCB 1.0 by aboler, RoomThermostat by henkjannl, Smart air by meeTeam05 and IoT-Environmental-Monitoring-System by Chethien1912.
The EL357N-G in open source designs
The gallery holds 11 open source boards using the EL357N-G from 7 GitHub repositories; a typical one measures about 90 × 54 mm and carries around 62 components.
100% are two-layer designs, the rest use four layers or more, and 91% carry an open source license.
The most starred is Plant Partner PCB 1.0 by aboler.
Parts used alongside the EL357N-G
Microcontrollers on boards using the EL357N-G
What boards using the EL357N-G are built for
EL357N-G: common questions
Where can I find a EL357N-G reference design?
Each of the 11 boards on this page is a real design using the EL357N-G. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the EL357N-G pin 1?
Pin 1 has a series resistor on 7 of 7 designs, most often 10 kΩ (then 680 Ω). Counted from the KiCad layouts of 7 open source designs using the EL357N-G.
How is the EL357N-G pin 2 connected?
Pin 2 is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the EL357N-G.
What resistor goes on the EL357N-G pin 3?
Pin 3 has a series resistor on 3 of 7 designs, most often 10 kΩ. Counted from the KiCad layouts of 7 open source designs using the EL357N-G.
What parts are used alongside the EL357N-G?
The AMS1117, RTC_DS3231M, 74HC14D,653 and ESP32-S3-DevKitC appear in the most repositories here.
Which microcontrollers do boards using the EL357N-G use?
Most are built on ESP32 (7).
How big is a typical board using the EL357N-G?
The median is 90 × 54 mm, and 100% are two-layer designs.
What is the most popular open source board using the EL357N-G?
By GitHub stars, Plant Partner PCB 1.0 by aboler, with 3 stars.
Can I simulate one of these boards using the EL357N-G before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.